NAVFAC Design-Build RFP Uniformat Structure

The Performance Technical Specifications (PTS) are organized to Level Two of the Uniformat II/Work Breakdown Structure (WBS). Within that structure, the information on particular subsystems is referenced through Level Three and Level Four WBS codes.

The Uniformat II/WBS was selected as the organizational structure for a number of reasons. The reasons included:

the widespread acceptance of Uniformat II as a systems approach to organizing building elements;
the systems based organizational structure readily lends itself to performance type specifications; and
consistency with other Government agencies' (e.g., GSA) organizing structure for projects, estimates, and criteria.

Final Combined Uniformat II / WBS 3/21/07, Revision 3

Section A - Substructure

Unf L1	Unf L2	Unf L3	WBS L4	Definition	E UOM	M UOM	Quantity Definition	WBS Ref No
A	SUBSTRUCTURE				SF	M2	Footprint area at grade	01
				This system includes all work below the lowest floor construction (usually slab-on-grade) and the enclosing horizontal and vertical elements required to form a basement, together with the necessary mass excavation and backfill.
	A10	FOUNDATIONS			SF	M2	Footprint area at grade
				Foundations includes the following Standard Foundations: wall and column foundations; foundation walls up to level of top of slab on grade; pile caps; foundation excavation, backfill, and compaction; footings and bases; perimeter insulation; perimeter drainage; anchor plates; and dewatering. Special Foundations include pile foundations, caissons, underpinning, dewatering, raft foundations, and pressure injected grouting. Slab on grade includes standard slab on grade, structural slab on grade, inclined slab on grade, trenches, pits and bases, and foundation drainage.
		A1010	STANDARD FOUNDATIONS		SF	M2	Footprint area at grade	0101
				Continuous footings, spread footings, grade beams, foundation walls, pile caps, and column piers.
			A101001	WALL FOUNDATIONS	LF	M	Length of footings and/or wall foundations	010101
				Continuous Footings - Assemblies include excavation, hand-shaped bottom, compacted backfill, formwork and keyway, reinforcing steel, concrete and screed finish.
				Foundation Walls - Include work items associated with CIP foundation walls, grade beams, or CMU walls. Assemblies include excavation, compacted backfill, perimeter insulation, perimeter drainage, formwork, reinforcing steel, concrete or CMU, and wall finish.
			A101002	COLUMN FOUNDATIONS & PILE CAPS	EA	EA	Number of footings, pile caps and/or piers	010102
				Spread Footings: Individual or part of continuous pier footings. Assemblies include excavation, backfill and compaction, formwork, reinforcing steel, and concrete and screed finish. If structural steel columns set directly on spread footings, anchor bolts are included in this assembly.
				Pile Caps - Assemblies include excavation if required (normally due to installation of piles, the subgrade is at desired level for pile cap), hand-shaped bottom, compacted backfill, formwork, reinforcing steel, and concrete and screed finish. If structural steel columns set directly on spread footings, anchor bolts are included in this assembly.
				Column Piers - Assemblies include formwork, reinforcing steel, concrete or CMU, finish, break ties and patch, and set anchor bolts.
			A101003	DEWATERING	SF	M2	Dewatered area
				Dewatering is the removal of water from excavations. The two principle methods of dewatering are by pump or by a system involving the sinking of a series of well-points around the area and extracting the water by suction pump. Assemblies would include pumps or well points and all associated dewatering materials and equipment.
			A101090	OTHER STANDARD FOUNDATIONS	XX	XX		01019X
				Standard foundations not described by the assembly categories listed above.
		A1020	SPECIAL FOUNDATIONS		SF	M2	Footprint area at grade	0102
				All work associated with special foundations including piles, caissons, and any other special foundation situation.
			A102001	PILE FOUNDATIONS	SF	M2	Footprint area at grade	010201
				CIP concrete piles, precast concrete piles, steel pipe piles, steel H-piles, step-tapered steel piles, and treated wood piles. Applicable assemblies would include the material for piles, pile driving, and pile cut-offs if required.
			A102002	CAISSONS	SF	M2	Footprint area at grade	010202
				Drilled Caissons - Assemblies include drilled caissons, steel casings if required, reinforcing steel, bell bottom excavation, concrete, and loading and hauling of excavated material.
			A102003	UNDERPINNING	LF	M	Length of underpinning	010203
				Underpinning is the provision of permanent support for existing buildings by extending their foundations to a new, lower level containing the desired bearing stratum. Assemblies include excavation, backfill, and underpinning materials.
			A102004	DEWATERING	SF	M2	Dewatered area	010204
				Dewatering is the removal of water from excavations. The two principle methods of dewatering are by pump or by a system involving the sinking of a series of well-points around the area and extracting the water by suction pump. Assemblies would include pumps or well points and all associated dewatering materials and equipment.
			A102005	RAFT FOUNDATIONS	SF	M2	Area of raft foundation	010205
				Raft foundations or spread foundations consist of a solid slab of heavily reinforced concrete covering the entire building footprint area.
			A102006	PRESSURE INJECTED GROUTING	SF	M2	Footprint area at grade	010206
				Assemblies provide for injecting cement grout for foundation stabilization.
			A102090	OTHER SPECIAL FOUNDATIONS	XX	XX		01029X
				These could include cofferdams, soil compaction foundations, and other special foundations. Assemblies would include all material and labor necessary to perform the work for the special foundation condition.
		A1030	SLAB ON GRADE		SF	M2	Footprint area at grade	0103
				A slab poured on earth, whether on undisturbed or fill soil.
			A103001	STANDARD SLAB ON GRADE	SF	M2	Area of slab	010301
				Standard slab-on-grade is supported by compacted earth or gravel fill. The soil bearing capacity is sufficient to support the slab. Assemblies include fine grade, gravel fill, underslab insulation, edge forms, termite treatment (interior slabs only), vapor barrier, reinforcing, expansion joints, control joints, and finish and curing. Assemblies are based on thickness of slab.
			A103002	STRUCTURAL SLAB ON GRADE	SF	M2	Area of slab	010302
				A structural slab-on-grade is not supported by compacted earth or gravel fill. The soil bearing capacity is insufficient to support the slab. A structural slab is generally a minimum of eight inches thick and will be reinforced with reinforcing bars rather than welded wire fabric. Assemblies include fine grade, gravel fill, underslab insulation, edge forms, termite treatment, (interior slabs only), vapor barrier, reinforcing, expansion joints, control joints, and finish and curing. Assemblies are based on thickness of slab.
			A103003	TRENCHES	LF	M	Length of trench	010304
				Cast-in-place trenches. Assemblies include excavation, hand-shaped bottoms, compacted backfill, formwork, reinforcing steel, concrete, and concrete finish. Examples include trench drains and dust trenches.
			A103004	PITS AND BASES	EA	EA	Number of pits and bases	010305
				Cast-in-place pits and bases. Assemblies include excavation, hand-shaped bottoms, compacted backfill, formwork, reinforcing steel, concrete, and concrete finish. Examples include elevator pits, dock leveler pits, oil change pits, and bases for equipment.
			A103005	FOUNDATION DRAINAGE	LF	M	Length of foundation	010306
				Foundation drainage directly associated with draining the foundation. This category does not include storm drainage piping for site. It would include drain pipe or drain tile at foundation or basement for specific purposes of draining foundation or basement. Assemblies would include excavation, hand-shaped bottoms, gravel, compacted backfill, and drain pipe, including accessories.
			A103090	OTHER LOWEST FLOOR CONSTRUCTION	XX	XX		01039X
				Lowest floor construction not described by the assembly categories listed above.
	A20	BASEMENT CONSTRUCTION			CY	M3	Volume of excavation
				Work Includes basement excavation, and basement walls.
		A2010	BASEMENT EXCAVATION		CY	M3	Volume of excavation	0104
				Excavation work associated with constructing a basement.
			A201001	EXCAVATION FOR BASEMENTS	CY	M3	Volume of excavation	010401
				All excavation, stockpiling, and hauling associated with basement excavations are included in this assembly.
			A201002	STRUCTURE BACKFILL & COMPACTION	CY	M3	Volume of backfill	010402
				All backfill including hauling in of suitable soils and all necessary compaction is included in this assembly.
			A201003	SHORING	SF	M2	Shoring contact area	010403
				This type of shoring is to resist horizontal pressure and not intended to carry vertical loads. Assemblies would include sheet piling or other material and labor used to hold back earth around the perimeter of an excavation.
			A201090	OTHER BASEMENT EXCAVATION	XX	XX		01049X
				Basement excavation not described by the assembly categories listed above.
		A2020	BASEMENT WALLS		SF	M2	Area of wall	0105
				Assembly includes basement perimeter walls that are below grade and below the ground floor level of the building; this also includes elevator pits and other pits.
			A202001	BASEMENT WALL CONSTRUCTION	SF	M2	Area of wall	010501
				This includes work items associated with CIP foundation walls or CMU walls and penetrations. Assemblies include formwork, reinforcing steel, concrete or CMU, and wall finish and curing.
			A202002	MOISTURE PROTECTION	SF	M2	Area of wall moisture protection	010502
				This assembly would be based on the type and square footage of waterproofing used on the foundation wall.
			A202003	BASEMENT WALL INSULATION	SF	M2	Area of wall insulation	010503
				This assembly would be based on the type and square footage of insulation used on the foundation wall.
			A202090	OTHER BASEMENT WALLS	XX	XX		01059X
				Basement walls not described by the assembly categories listed above.

Section B - Shell

Unf L1	Unf L2	Unf L3	WBS L4	Definition	E UOM	M UOM	Quantity Definition	WBS Ref No
B	SHELL				SF	M2	Area of supported floors
				This system includes all structural slabs, and decks and supports within basements and above grade. Note that the structural work will include both horizontal items (slabs, decks, etc.) and vertical structural components (columns and interior structural walls). Exterior load bearing walls are not included in this system but in System B2010, Exterior Walls.
	B10	SUPERSTRUCTURE			SF	M2	Area of supported floors	02
				Work includes floor construction and roof construction.
		B1010	FLOOR CONSTRUCTION		SF	M2	Area of supported floors	0201
				This construction can be wood, concrete, CMU, steel frame, etc.
			B101001	STRUCTURAL FRAME	SF	M2	Area of supported floors	020101
				The structural frame could consist of structural steel including columns, beams, joists, and all associated items. It could be a concrete frame utilizing concrete or masonry columns and concrete girders and beams. The structural frame could be wood columns with wood beams or wood trusses. The structural frame could be a combination of the above. For example, concrete or masonry columns with structural steel beams and joists. All associated work items should be included in each assembly. Separate assemblies would be used for different types of construction. The unit of measure at the assembly level is the square footage of the supported area. Decks and slabs are not included in this assembly.
			B101002	STRUCTURAL INTERIOR WALLS	SF	M2	Area of wall	020102
				Assemblies would be CIP or CMU walls or other structural interior walls. The assemblies would include the labor and material required to perform the construction tasks associated with this type of wall.
			B101003	FLOOR DECKS AND SLABS	SF	M2	Area of supported floors	020103
				Slabs above grade should be broken into assemblies according to their particular type of construction (i.e., flat slab, pan slab, precast or pre-stressed slab, four-way slab, slabs on metal or wood decking with concrete fill, etc.). All associated work items should be included in each assembly, such as expansion and contraction joints.
			B101004	INCLINED AND STEPPED FLOORS	SF	M2	Area of inclined & stepped floors
				This assembly should be broken down according to their particular type of construction (i.e., flat slab, pan slab, precast or pre-stressed slab, four-way slab, slabs on metal or wood decking with concrete fill, etc.). All associated work items should be included in each assembly, such as expansion and contraction joints.
			B101005	BALCONY CONSTRUCTION	SF	M2	Area of supported balconies	020104
				Balconies above grade should be broken into assemblies according to their particular type of construction. All associated items including handrails should be included in the assembly.
			B101006	RAMPS	SF	M2	Area of supported ramps	020105
				Ramps above grade should be broken into assemblies according to their type of construction. All associated items including handrails should be included in the assembly.
			B101007	FLOOR RACEWAY SYSTEMS	SF	M2	Gross floor area	020106
				Under floor or in-slab conduit including conduit and all associated devices.
			B101090	OTHER FLOOR CONSTRUCTION	XX	XX		02019X
				Any type of special floor construction not included above would fall in this category, such as catwalks, space frames, etc. All associated work items would be included in the assembly.
		B1020	ROOF CONSTRUCTION		SF	M2	Area of supported roof	0202
				This construction is similar to floor construction except that is applies to the framework supporting the roof and roof decks. (See also System B30 Roofing.)
			B102001	STRUCTURAL FRAME	SF	M2	Area of supported roof	020201
				The structural frame could consist of structural steel including columns, beams, joists, and all associated items. It could be a concrete frame utilizing concrete or masonry columns and concrete girders and beams. The structural frame could be wood columns with wood beams or wood trusses. The structural frame could be a combination of the above. For example, concrete or masonry columns with structural steel beams and joists. All associated work items should be included in each assembly. Separate assemblies would be used for different types of construction. The unit of measure at the assembly level is the square footage of the supported area. Decks and slabs are not included in this assembly.
			B102002	STRUCTURAL INTERIOR WALLS	SF	M2	Area of walls	020202
				Assemblies would be CIP or CMU walls or other structural interior walls. The assemblies would include the labor and material required to perform the construction tasks associated with this type of wall.
			B102003	ROOF DECKS AND SLABS	SF	M2	Area of supported roof	020203
				Roof decks and slabs should be broken into assemblies according to their particular type of construction (i.e., flat slab, pan slab, precast or pre-stressed slab, four-way slab, slabs on metal or wood decking with concrete fill, etc.). All associated work items should be included in each assembly.
			B102004	CANOPIES	SF	M2	Area of supported canopies	020204
				Canopies should be broken into assemblies according to their particular type of construction (i.e., flat slab, pan slab, precast or pre-stressed slab, four-way slab, slabs on metal or wood decking with concrete fill, etc.). All associated work items should be included in each assembly.
			B102090	OTHER ROOF CONSTRUCTION	SF	M2	Area of supported roof	02029X
				Any type of special roof construction not included above would fall into this category. All associated work items would be included in this assembly.
	B20	EXTERIOR ENCLOSURE			SF	M2	Area of exterior walls	03
				This system consists of the exterior facing of the facility, which includes all vertical and horizontal exterior closure such as exterior walls, exterior windows, and exterior doors. This system excludes roofing (See System B30, Roof). Load bearing exterior walls will be included here, and not in System B10, Superstructure. Structural frame elements at exterior such as columns, beams, spandrels, etc., would be included in Superstructure with only the applied exterior finishes (i.e., paint, stucco, etc.) being included here. Finishes to the inside face of walls which are not an integral part of the wall construction will be included in System C30, Interior Finishes.
		B2010	EXTERIOR WALLS		SF	M2	Area of exterior walls	0301
				All materials associated with the following construction: exterior load-bearing walls, insulation and vapor barrier, parapets, exterior louvers and screens, sun control devices (exterior), balcony walls and handrails, exterior soffits, screen walls, and exterior coatings.
			B201001	EXTERIOR CLOSURE	SF	M2	Area of exterior walls	030101
				Assemblies would include material contained in exterior closure wall, such as masonry with brick veneer. Materials used for interior finishes on exterior walls are not included in this assembly. For example, if the interior side of this masonry wall is sheetrock applied on metal furring strips, the masonry wall is included in this assembly, but the furring strips and sheetrock are categorized as C3010 WALL FINISHES.
			B201002	EXTERIOR WALL BACKUP CONSTRUCTION	SF	M2	Area of backup walls
				Assemblies used to support structure for the exterior skin and/or provide load-bearing walls for the facility. Materials used for interior finishes on exterior walls are not included in this assembly. For example, if the interior side of this masonry wall is sheetrock applied on metal furring strips, the masonry wall is included in this assembly, but the furring strips and sheetrock are categorized as C3010 WALL FINISHES.
			B201003	INSULATION & VAPOR RETARDER	SF	M2	Area of insulation	030102
				Assemblies would include all types of insulation associated with the exterior wall. Rigid, batt and poured insulation should be separated into different assemblies.
			B201004	PARAPETS	LF	M	Length of parapets	030104
				Assemblies include materials used in association with parapets. Parapets are long walls or railings usually along the edge of a roof or balcony.
			B201005	EXTERIOR LOUVERS & SCREENS	SF	M2	Area of louvers and screens	030105
				Assemblies include louvers and screens which are located in exterior walls. The unit of measure at the assembly level is each.
			B201006	BALCONY WALLS & HANDRAILS	LF	M	Length of walls and handrails	030107
				Assemblies would include materials associated with balcony walls and handrails. These rails are usually guardrails and not associated with stairs.
			B201007	EXTERIOR SOFFITS	SF	M2	Area of soffits	030108
				Assemblies would include all associated materials which make up the soffit and supports for the soffit. Typical materials would include wood, aluminum, exterior grade gypboard, stucco, etc.
			B201008	FLASHING	SF	M2	Area of flashings
				Assemblies include all flashings associated with the exterior walls except for thru-wall flashing.
			B201009	EXTERIOR PAINTING AND SPECIAL COATINGS	SF	M2	Area of exterior coatings
				Assemblies include paint, stucco, etc. The unit of measure at the assembly level is area of exterior coatings.
			B201010	EXTERIOR JOINT SEALANT	LF	M	Length of sealants
				Exterior application of joint sealants to seal joints and prepare for finish material installation.
			B201011	SUN CONTROL DEVICES	SF	M2	Area of sun control devices	030106
				Assemblies include awnings, shades, and solar panels attached to the exterior of the building. A separate assembly should be used for each type of sun control device.
			B201012	SCREEN WALLS	LF	M	Length of screen wall
				Exterior screen walls used for security purposes immediately adjacent to the building such as screen walls at a loading dock. Assemblies would include materials associated with all types of walls. This can also include visual barriers on the roof to screen equipment. Note that perimeter fencing that is typically more than five feet from the building's exterior is included in sitework rather than in this system.
			B201090	OTHER EXTERIOR WALLS	XX	XX		03019X
				Exterior walls not described by the assembly categories listed above.
		B2020	EXTERIOR WINDOWS		SF	M2	Area of windows	0302
				All windows located in exterior walls or exterior skin.
			B202001	WINDOWS	SF	M2	Area of windows	030201
				Fixed or operable windows located in exterior walls or exterior skin. Assemblies would include frames, glazing, caulking, finishes and other associated work.
			B202002	STOREFRONTS	SF	M2	Area of storefronts	030202
				Fixed storefronts including associated doors in exterior walls or exterior skin. Assemblies would include integral storefront doors, frames, glazing, caulking, finishes, and other associated work.
			B202003	CURTAIN WALLS	SF	M2	Area of curtain walls	030203
				This applies to glass curtain walls and spandrel glass in exterior walls or exterior skin. Assemblies would include integral curtainwall doors, frames, glazing, caulking, finishes, and other associated work.
			B202004	EXTERIOR GLAZING	SF	M2	Area of Glazing
			B202090	OTHER EXTERIOR WINDOWS	XX	XX		03029X
				Exterior windows not described by the assembly categories listed above.
		B2030	EXTERIOR DOORS		EA	EA	Number of doors	0303
				All doors located in exterior walls or exterior skin.
			B203001	SOLID DOORS	EA	EA	Number of doors	030302
				Assemblies include all exterior solid doors, hollow metal or wood with frames. Solid doors may include glazing lites in doors. Door hardware is located in B203008 EXTERIOR DOOR HARDWARE.
			B203002	GLAZED DOORS	EA	EA	Number of doors	030301
				Assemblies include all full glazed exterior doors with glass, frames not included in storefront and curtainwalls. These doors can be made of storefront materials but are not part of a curtainwall or storefront. Door hardware is located in B203008 EXTERIOR DOOR HARDWARE.
			B203003	REVOLVING DOORS	EA	EA	Number of doors	030303
				Assemblies include all revolving doors at exterior of the facility.
			B203004	OVERHEAD AND ROLL-UP DOORS	SF	M2	Area of doors	030401
				Overhead and roll-up doors installed in exterior walls or exterior skin. Assemblies include frames, hardware, hoisting devices, and finish and other associated work. The unit of measure at the assembly level is each door.
			B203005	HANGAR DOORS	SF	M2	Area of doors	030402
				Large aircraft doors used on medium and high bay hangars. Assemblies would include frames, hardware, hoisting devices, and finish and other associated work.
			B203006	BLAST RESISTANT DOORS	SF	M2	Area of doors	030403
				Special exterior doors used for blast resistance. Assemblies would include frames, hardware, hoisting devices, and finish and other associated work.
			B203007	GATES	SF	M2	Area of doors	030404
				Any special gate type used in the exterior wall or exterior skin of the building. Assemblies would include frames, hardware, hoisting devices, and finish and other associated work. The unit of measure at the assembly level is each gate.
			B203008	EXTERIOR DOOR HARDWARE	EA	EA	Number of doors
				Exterior door hardware includes items such as closers, hinges, locksets, panic hardware, etc.
			B203090	OTHER EXTERIOR SPECIALTY DOORS	XX	XX		03049X
				Any special type door used in the exterior wall or exterior skin of the building. Assemblies would include frames, hardware, hoisting devices, and finish and other associated work. The unit measure at the assembly level is each door, or area of special doors, i.e., hangar doors.
			B203091	OTHER EXTERIOR PERSONNEL DOORS	XX	XX		03039X
				Exterior personnel doors not described by the assembly categories listed above.
	B30	ROOFING			SF	M2	Gross area of roof	04
				This System includes all waterproof roof coverings and insulation, expansion joints, together with skylights, hatches, ventilators, and all required trim. In addition to roof coverings, the system includes all waterproof membranes and traffic toppings over below grade enclosed areas, balconies, and the like.
		B3010	ROOF COVERINGS		SF	M2	Gross area of roof	0401
				This System includes all waterproof roof coverings and insulation, expansion joints, together with skylights, hatches, ventilators, and all required trim. In addition to roof coverings, the system includes all waterproof membranes and traffic toppings over below grade enclosed areas, balconies, and the like.
			B301001	STEEP SLOPE ROOF SYSTEMS	SF	M2	Area of roof covering	040101
				Assemblies include roof coverings such as shingle, wood shake, structural standing seam, metal roofing, etc.
			B301002	LOW SLOPE ROOF SYSTEMS	SF	M2	Area of topping or membrane
				Assemblies include roof coverings such as built-up, elastomeric, modified bitumen, etc. Also, walkways and work areas (used to gain access to rooftop equipment) will be included here.
			B301003	ROOF INSULATION & FILL	SF	M2	Area of insulation	040103
				Assemblies include all types of insulation associated with the roof area.
			B301004	FLASHINGS & TRIM	SF	M2	Area of flashings	040104
				Assemblies include all flashings associated with the roof, i.e., eave flashing, gable flashing, etc.
			B301005	GUTTERS & DOWNSPOUTS	LF	M	Length of gutters and downspouts	040106
				Assemblies include all gutters, downspouts, and associated work including splash blocks.
			B301006	ROOF OPENINGS AND SUPPORTS	SF	M2	Area of openings	040105
				All roof penetrations including roof hatches, sky lights, area glazing, gravity roof ventilators, smoke vents, etc.
			B301090	OTHER ROOFING	XX	XX		04019X
				Roofing not described by the assembly categories listed above.

Section C - Interiors

Unf L1	Unf L2	Unf L3	WBS L4	Definition	E UOM	M UOM	Quantity Definition	WBS Ref No
C	INTERIOR				SF	M2	Gross floor area	05
				Construction which takes place inside the exterior wall or exterior closure. The system does not include interior structural walls, which are included in B1010 FLOOR CONSTRUCTION and B1020 ROOF CONSTRUCTION.
	C10	INTERIOR CONSTRUCTION			SF	M2	Gross floor area
				This assembly includes partitions, interior doors, and specialties.
		C1010	PARTITIONS		SF	M2	Area of partitions	0501
				Includes all interior partitions.
			C101001	FIXED PARTITIONS	SF	M2	Area of fixed partition walls	050101
				Interior fixed partitions include metal or wood studs, sheetrock, masonry, and concrete walls.
			C101002	DEMOUNTABLE PARTITIONS	SF	M2	Area of demountable partition walls	050102
				Assemblies would include all demountable partitions and associated work including tracks and anchoring systems.
			C101003	RETRACTABLE PARTITIONS	SF	M2	Area of retractable partition walls	050103
				Assemblies would include all retractable or folding partitions and associated work including tracks and anchoring systems.
			C101004	INTERIOR GUARDRAILS & SCREENS	LF	M	Length of balustrades and screens	050104
				Assemblies include balustrades (balcony handrails and the row screen of posts that support them) and screens and associated work including tracks and anchoring systems. These balustrades/guardrails are related to interior balconies and are not associated with stairs.
			C101005	INTERIOR WINDOWS	SF	M2	Area of windows	050105
				Fixed or operable windows. Assemblies would include frames, glazing, caulking and other associated work.
			C101006	GLAZED PARTITIONS & STOREFRONTS	SF	M2	Area of partitions and storefronts	050106
				Fixed interior glazed partitions including interior storefronts with doors. Assemblies include frames, glazing, caulking, and other associated work.
			C101007	INTERIOR GLAZING	SF	M2	Area of interior glazing
			C101008	INTERIOR JOINT SEALANT	LF	M	Length of sealants
				Interior application of sealants to seal joints and prepare for finish material installation. The application shall include partitions, doors and fitting.
			C101090	OTHER PARTITIONS	XX	XX		05019X
				Interior partitions not described by the assembly categories listed above.
		C1020	INTERIOR DOORS		LEF	LEF	Number of leaves	0502
				All interior doors.
			C102001	STANDARD INTERIOR DOORS	LEF	LEF	Number of leaves	050201
				Assemblies include all standard interior wood or hollow metal doors with frames, finish, etc. Standard interior door may include vision lites. Interior door hardware is located in C102007 INTERIOR DOOR HARDWARE.
			C102002	GLAZED INTERIOR DOORS	LEF	LEF	Number of leaves	050202
				Assemblies include all glazed interior doors with glass, frames, finish, including storefront, etc. Interior door hardware is located in C102007 INTERIOR DOOR HARDWARE.
			C102003	FIRE DOORS	LEF	LEF	Number of leaves	050203
				Assemblies include all interior fire doors, including all necessary frames, and sensing devices integral with the door. Interior door hardware is located in C102007 INTERIOR DOOR HARDWARE.
			C102004	SLIDING & FOLDING DOORS	SF	M2	Area of sliding or folding door	050204
				Assemblies include all sliding and folding doors with frames, hardware, locking devices, tracks, and supporting systems. The unit of measure at the assembly level is each.
			C102005	INTERIOR OVERHEAD DOORS	SF	M2	Area of doors	050301
				Overhead doors installed in the interior of a facility. Assemblies include frames, hardware, hoisting devices, and finish and other associated work. The unit of measure at the assembly level is each door.
			C102006	INTERIOR GATES	SF	M2	Area of gates	050302
				Any special type gate installed in the interior of a facility. Assemblies include frames, hardware, hoisting devices, and finish and other associated work. The unit measure at the assembly level is each gate.
			C102007	INTERIOR DOOR HARDWARE	EA	EA	Number of doors
				Interior door hardware includes items such as closers, hinges, locksets, panic hardware, etc.
			C102090	OTHER INTERIOR SPECIALTY DOORS	XX	XX		05039X
				Any special type door installed in the interior of a facility. Assemblies include frames, hardware, hoisting devices, and finish and other associated work. The unit measure at the assembly level is each gate.
			C102091	OTHER INTERIOR PERSONNEL DOORS	XX	XX		05029X
				Interior personnel doors not described by the assembly categories listed above.
		C1030	SPECIALTIES		SF	M2	Gross floor area	0504
				Most commonly used specialty items.
			C103001	COMPARTMENTS, CUBICLES & TOILET PARTITIONS	EA	EA	Number of compartments, cubicles, or toilet partitions	050401
				Assemblies include individual compartments, cubicles, toilet partitions, and urinal screens.
			C103002	TOILET & BATH ACCESSORIES	EA	EA	Number of accessories	050402
				Toilet and bath accessories. For example, soap dispensers, toilet paper holder, towel dispensers, grab bars, bathroom mirrors, etc.
			C103003	MARKER BOARDS & TACK BOARDS	EA	EA	Each Board	050403
				Assemblies include all marker boards, tackboards, and fastening devices. The unit of measure at the assembly level is each.
			C103004	IDENTIFYING DEVICES	EA	EA	Number of identifying devices	050404
				Assemblies include all signs, plaques, traffic markers, etc.
			C103005	LOCKERS	EA	EA	Number of lockers	050405
				Assemblies include all types of lockers, either wood or metal, single or double tier. Special bases used for lockers would be included in this assembly.
			C103006	SHELVING	LF	M	Length of shelving	050406
				Assemblies include all types of shelving with brackets and all supporting materials and finish, if required.
			C103007	FIRE EXTINGUISHER CABINETS	EA	EA	Number of fire extinguisher cabinets	050407
				This assembly would include all types and sizes of fire extinguisher cabinets. Fire extinguishers are not included in this assembly; they are included in D40.
			C103008	COUNTERS	LF	M	Length of counters	050501
				Assemblies include all counters and countertops with all necessary brackets and supporting materials and finish, if required.
			C103009	CABINETS	LF	M	Length of cabinets	050502
				This assembly includes all cabinetry and millwork items with associated accessories and anchoring devices. Cabinet finishes are included in this assembly. Metal cabinets and special use cabinetry (medical, dental, libraries, etc.) are included in C103010 CASEWORK.
			C103010	CASEWORK	LF	M	Length of casework
				Assemblies would include built-in premanufactured cabinetry for specialized functions such as labs, libraries, medical and dental facilities.
			C103011	CLOSETS	LF	M	Length of closets	050503
				This assembly includes all built-in closets with all associated work and finishes. These closets are millwork items or prefabricated coat closets for schools and dormitories.
			C103012	FIRESTOPPING PENETRATIONS	EA	EA	Each Penetration
				Assembly includes sleeve, caulking, and flashing.
			C103013	SPRAYED FIRE-RESISTIVE MATERIALS	SF	M2	Area of coverage
				Sprayed Fire-Resistive Materials includes materials that are applied primarily to a building's framework (columns, beams, bracing, metal decking) to prevent structural failure.
			C103014	ENTRANCE FLOOR GRILLES AND MATS	SF	M2	Area of grilles/mats
				Assemblies include floor grilles and mats installed in a fixed arrangement at a building entrance.
			C103015	ORNAMENTAL METALWORK	EA	EA	Number of metalwork items
				Building components made from ornamental metals. Ornamental stair handrails are included in B1010 EXTERIOR STAIRS and C20 STAIRS.
			C103090	OTHER INTERIOR SPECIALTIES	EA	EA	Number of specialty items	05049X
				Interior specialties not described by the assembly categories listed above.
	C20	STAIRS			FLT	FLT	Number of flights
				Work includes all stair construction.
		C2010	STAIR CONSTRUCTION		FLT	FLT	Number of flights	0203
				All work items located within the building footprint. A flight of stairs is considered to be all the treads and risers with landings required to travel from one floor to the next.
			C201001	INTERIOR AND EXTERIOR STAIRS	FLT	FLT	Number of flights	020301
				All stair work items associated with non-fire escape stairs. The stairs can be either interior stairs or stairs exposed to the weather. Exterior stairs are exposed to the outside and do not typically require HVAC. A flight of stairs is considered to be all the treads and risers with landings required to travel from one floor to the next.
			C201002	FIRE ESCAPE STAIRS	FLT	FLT	Number of flights
				Assemblies include exterior stairs which are used for emergency egress. These stairs are exposed to the weather. Handrails, finishes and associated work items are included in this assembly.
			C201090	STAIR HANDRAILS, GUARDRAILS AND ACCESSORIES	XX	XX		02039X
				Stair handrails, guardrails, and cast-in-place nosings for interior and exterior stairs.
	C30	INTERIOR FINISHES			SF	M2	Area of finishing	06
				Includes wall finishes, floor finishes, and ceiling finishes.
		C3010	WALL FINISHES		SF	M2	Area of finished walls	0601
				Finishes which are applied to interior wall surfaces. For coatings, refer to C3040.
			C301001	CONCRETE WALL FINISHES	SF	M2	Area of finished walls	060101
				This assembly would include a concrete finish applied directly to an interior wall surface. This assembly does not include items that directly apply to wall finishes covered elsewhere in this subsystem.
			C301002	PLASTER WALL FINISHES	SF	M2	Area of finished walls	060102
				This assembly includes plaster or stucco applied directly to an interior wall surface. Lath and associated work would be included in this assembly. This assembly does not include items that directly apply to wall finishes covered elsewhere in this subsystem.
			C301003	GYPSUM WALLBOARD FINISHES	SF	M2	Area of finished walls	060103
				This assembly includes gypsum wallboard applied directly to an interior wall surface. Furring strips or channels are included in this assembly. This assembly also includes taping, sanding, finishing, and sheetrock accessories. This assembly does not include items that directly apply to wall finishes covered elsewhere in this subsystem.
			C301004	TILE & TERRAZZO WALL FINISHES	SF	M2	Area of finished walls	060104
				This assembly includes tile and terrazzo applied directly to an interior wall surface. Each type of tile would be a separate assembly.
			C301005	WALL COVERINGS	SF	M2	Area of wall coverings	060106
				This assembly includes wall coverings and protective strips applied directly to an interior wall surface.
			C301006	ACOUSTICAL PANELS ADHERED TO WALLS	SF	M2	Area of acoustical tiles and panels	060107
				This assembly includes acoustical tiles and panels with associated work applied directly to an interior wall surface.
			C301090	OTHER WALL FINISHES	XX	XX		06019X
				Assemblies include finishes to wall types not included above. These include, but are not limited to, different types of shielding and the work and materials associated with each.
		C3020	FLOOR FINISHES		SF	M2	Area of finished floors	0602
				All flooring and floor finishes applied to interior floors. For coatings refer to C3040.
			C302001	TILE FLOOR FINISHES	SF	M2	Area of tile floors	060201
				Assemblies include ceramic, quarry, and other non-resilient tile floors.
			C302002	TERRAZZO FLOOR FINISHES	SF	M2	Area of terrazzo floors	060202
				Assemblies include terrazzo floors.
			C302003	WOOD FLOORING	SF	M2	Area of wood floors	060203
				Assemblies include wood floors.
			C302004	RESILIENT FLOOR FINISHES	SF	M2	Area of resilient floors	060204
				Assemblies include resilient floors.
			C302005	CARPETING	SF	M2	Area of carpeting	060205
			C302006	MASONRY & STONE FLOORING	SF	M2	Area of masonry or stone flooring	060206
				Assemblies include masonry, concrete pavers, and stone flooring.
			C302007	WALL BASE FINISHES	LF	M	Length of wall base
				Assemblies include wall base, consisting of various materials such as vinyl, ceramic tile, etc.
			C302008	STAIR FINISHES	SF	M2	Area of coverage
				Includes field-applied finish materials (other than paint) to surfaces of stairs including treads, risers and landings.
			C302009	FLOOR TOPPINGS AND TRAFFIC MEMBRANES	SF	M2	Area of coverage
				Assemblies include floor toppings and membrane systems.
			C302010	HARDENERS AND SEALERS	SF	M2	Area of coverage
				Assemblies include floor hardeners and sealers, typically applied on concrete floors.
			C302011	RAISED ACCESS FLOORING	SF	M2	Area of special flooring
				Assemblies include all types of raised flooring, pedestal access floors and other types of access flooring.
			C302090	OTHER FLOORING & FLOOR FINISHES	XX	XX		06029X
				Assemblies include floor finishes not described by the assembly categories listed above, such as conductive, armored, etc.
		C3030	CEILING FINISHES		SF	M2	Area of ceilings	0603
				All ceilings and ceiling finishes applied to interiors. For coatings, refer to C3040.
			C303001	ACOUSTICAL CEILING TILES & PANELS	SF	M2	Area of acoustical ceilings	060304
				Assemblies include acoustical ceiling tiles and panels. The suspension system, if required, is in Assembly Category C303005. This assembly does not include items that directly apply to ceiling finishes covered elsewhere in this subsystem.
			C303002	GYPSUM WALLBOARD CEILING FINISHES	SF	M2	Area of gypsum ceilings	060303
				Assemblies include gypsum wallboard applied to interior ceilings. Furring strips or channels are included in this assembly if they are applied directly to the ceiling surface. If the gypsum board is applied to a suspended ceiling system, the suspended system would be in Assembly Category C303005. This assembly does not include items that directly apply to ceiling finishes covered elsewhere in this subsystem.
			C303003	PLASTER CEILING FINISHES	SF	M2	Area of plaster ceiling finish	060302
				Assemblies include plaster or stucco finishes applied to interior ceilings. Lath and associated work would apply to this assembly. This assembly does not include items that directly apply to ceiling finishes covered elsewhere in this subsystem.
			C303004	WOOD CEILINGS	SF	M2	Area of wood ceilings	060305
				Assemblies include wood ceilings. Different types of wood ceilings should be separated into different assemblies. If the wood ceiling is applied to a suspended ceiling system, the suspended system would be in Assembly Category C303005. This assembly does not include items that directly apply to ceiling finishes covered elsewhere in this subsystem.
			C303005	SUSPENSIONS SYSTEMS	SF	M2	Area of suspension system	060307
				This assembly includes any suspension system which is suspended or hung from the structure for the purpose of fastening a ceiling.
			C303006	METAL STRIP CEILINGS	SF	M2	Area of metal ceiling	060308
				Assemblies include all metal strip materials applied to ceilings.
			C303090	OTHER CEILING & CEILING FINISHES	XX	XX		06039X
				Special ceilings and ceiling finishes not described by the assembly categories listed above.
		C3040	INTERIOR COATINGS AND SPECIAL FINISHES		SF	M2	Area of interior coatings
				This assembly includes surface preparation and application of coatings to interior surfaces.
			C304001	GENERAL REQUIREMENTS	SF	M2	Area of coatings and finishes	0
			C304002	CONCRETE FINISHES	SF	M2	Area of concrete finishes	0
			C304003	CONCRETE MASONRY FINISHES	SF	M2	Area of concrete masonry finishes	0
			C304004	METAL FINISHES	SF	M2	Area of metal finishes	0
			C304005	INTERIOR WOOD FINISHES	SF	M2	Area of wood finishes	0
			C304006	GYPSUM WALLBOARD FINISHES	SF	M2	Area of gypsum wallboard coatings	0
			C304007	SPECIAL COATINGS ON WALLS	SF	M2	Area of special wall coatings	0

Section D - Services

Unf L1	Unf L2	Unf L3	WBS L4	Definition	E UOM	M UOM	Quantity Definition	WBS Ref No
D	SERVICES				EA	EA
				Includes all methods of conveying, plumbing, HVAC, fire protection, and electrical.
	D10	CONVEYING			STY	STY	Number of stories	07
				This system includes elevators, escalators, pneumatic tube systems, conveyors, chutes, etc. Foundations for these systems are included in System A, Substructure.
		D1010	ELEVATORS AND LIFTS		STP	STP	Number of stops	0701
				Includes passenger elevators and freight elevators.
			D101001	GENERAL CONSTRUCTION ITEMS	EA	EA	Number of items	070101
				Includes construction work, other than conveying system work, which must be performed in conjunction with this type of work to complete the system.
			D101002	PASSENGER ELEVATORS	STP	STP	Number of stops	070102
				The unit measure at the assembly level is each stop.
			D101003	FREIGHT ELEVATORS	STP	STP	Number of stops	070103
				The unit measure at the assembly level is each stop.
			D101004	WHEELCHAIR LIFT	EA	EA	Number of lifts
				Premanufactured lift to gain wheelchair access.
			D101005	DUMBWAITERS	STP	STP	Number of stops
				The unit measure of the assembly is each stop.
			D101090	OTHER VERTICAL TRANSPORTATION EQUIPMENT	XX	XX		07019X
				This includes elevators not described by the assembly categories listed above, such as people lifts.
		D1020	WEIGHT HANDLING EQUIPMENT		EA	EA	Number of items	0
			D102001	BASIC REQUIREMENTS OF CRANES AND MONORAILS	EA	EA	Number of items	0
			D102002	OVERHEAD CRANES	EA	EA	Number of items	0
			D102003	MONORAILS	EA	EA	Number of items	0
		D1030	ESCALATORS AND MOVING WALKS		LF	M	Length of stairs or walks	0702
			D103001	ESCALATORS	LF	M	Length of stairs	070201
			D103002	MOVING WALKS	LF	M	Length of walks	070202
			D103090	OTHER MOVING STAIRS & WALKS	XX	XX		07029X
				Moving stairs or walks not described by the assembly categories listed above.
		D1090	OTHER CONVEYING SYSTEMS		EA	EA	Number of systems
				Other conveying systems includes pneumatic tube systems, conveyor belts, chutes, and transportation systems.
			D109001	PNEUMATIC TUBE SYSTEMS	EA	EA	Number of systems	070306
			D109002	CONVEYORS	EA	EA	Number of material handling systems
			D109003	LINEN, TRASH, AND MAIL CHUTES	LF	M	Length of chute
			D109004	TURNTABLES	EA	EA	Number of turntables
			D109005	OPERABLE SCAFFOLDING	SF	M2	Area of scaffolding
			D109006	TRANSPORTATION SYSTEMS	EA	EA	Number of systems
				This assembly includes baggage handling and aircraft loading systems.
			D109090	OTHER MATERIAL HANDLING SYSTEMS	XX	XX		07039X
				Material or handling systems not described by the assembly categories listed above.
	D20	PLUMBING			EA	EA	Number of fixtures	08
				The plumbing system's primary function is the transfer of liquids and gases. This system includes all water supply and waste items within the building.
		D2010	PLUMBING FIXTURES		EA	EA	Number of fixtures	0801
				All terminal devices on the domestic plumbing system which have water supplied to the fixture. Hot water heaters, hose bibbs, and special equipment are not counted as a fixture.
			D201001	WATERCLOSETS	EA	EA	Number of fixtures	080101
			D201002	URINALS	EA	EA	Number of fixtures	080102
			D201003	LAVATORIES	EA	EA	Number of fixtures	080103
			D201004	SINKS	EA	EA	Number of fixtures	080104
			D201005	SHOWERS/TUBS	EA	EA	Number of fixtures	080105
			D201006	DRINKING FOUNTAINS & COOLERS	EA	EA	Number of fixtures	080106
			D201007	BIDETS	EA	EA	Number of fixtures
			D201090	EMERGENCY FIXTURES	XX	XX
				Emergency fixtures not described by the assembly categories listed above.
		D2020	DOMESTIC WATER DISTRIBUTION		EA	EA	Number of fixtures	0802
				This system provides for human health and comfort. The water supply needed is determined by the number of fixtures attached. Hot water heaters, hose bibbs, and special equipment are not counted as a fixture.
			D202001	PIPES & FITTINGS	EA	EA	Number of fixtures	080201
				Assemblies include all pipe, fittings, and associated work with regard to domestic water supply. The unit of measure at the assembly level is number of fixtures.
			D202002	VALVES & HYDRANTS	EA	EA	Number of valves and hydrants	080202
				Assemblies include all valves and hydrants. Hose bibbs are included in this assembly. The unit of measure at the assembly level is number of valves and hydrants.
			D202003	DOMESTIC WATER EQUIPMENT	EA	EA	Number of fixtures	080501
				This assembly includes equipment associated with the domestic water supply, including fittings, and specialties required for hook-up. Assemblies include hot water heaters, water treatment plant, i.e., water softeners, filters, distillers, etc.; pumps directly associated with domestic water supply; and tanks for the potable hot or cold water system. The unit of measure at the assembly level is pieces of equipment.
			D202004	INSULATION & IDENTIFICATION	EA	EA	Number of fixtures	080204
				Assemblies include insulation used in association with domestic water supply. The unit of measure at the assembly level is number of fixtures.
			D202005	SPECIALTIES	EA	EA	Pieces of equipment	080205
				Any other special items associated with domestic water supply. All associated work items, including pipes, fittings, valves, insulation, and hook-up should be included in this assembly. The unit of measure at the assembly level is pieces of special equipment.
			D202090	OTHER DOMESTIC WATER SUPPLY	XX	XX		08029X
				Domestic water supply not described by the assembly categories listed above.
		D2030	SANITARY WASTE		EA	EA	Number of fixtures	0803
				This system provides for human health and comfort. Fixtures include all terminal devices which have a water supply (except water supply equipment and specialties), and also devices that transfer fluids into the sanitary waste system that do not have a water supply. Floor drains (not drain hubs) are included as a sanitary waste fixture.
			D203001	WASTE PIPE & FITTINGS	EA	EA	Number of fixtures	080302
				Assemblies include all pipe, fittings, and associated work with regard to sanitary waste pipe and fittings. The unit of measure at the assembly level is number of fixtures.
			D203002	VENT PIPE & FITTINGS	EA	EA	Number of fixtures	080302
				Assemblies include all pipe, fittings, and associated work with regard to sanitary vent pipe and fittings. The unit of measure at the assembly level is number of fixtures.
			D203003	FLOOR DRAINS	EA	EA	Number of floor drains	080303
				Assemblies include all floor drains. Hub drains are considered to be pipe and are not included in this category. The unit of measure at the assembly level is number of drains.
			D203004	SANITARY AND VENT EQUIPMENT	EA	EA	Number of fixtures	080502
				This is equipment associated with the sanitary waste system, including fittings and specialties required for hook-up. Assemblies include waste treatment equipment, i.e., sluice gates, incinerators, etc.; pumps for sewage injection; and holding tanks for the domestic water system. The unit of measure at the assembly level is pieces of equipment.
			D203005	INSULATION & IDENTIFICATION	EA	EA	Number of fixtures	080304
				Assemblies include insulation used in association with sanitary waste and vent system. The unit of measure at the assembly level is number of fixtures.
			D203090	OTHER SANITARY WASTE	XX	XX		08039X
				Sanitary waste and vent not described by the assembly categories listed above.
		D2040	RAIN WATER DRAINAGE		SF	M2	Area of roof	0804
				Roof drainage system. Gutter and downspouts are not included in this subsystem.
			D204001	PIPE & FITTINGS	LF	M	Length of pipe	080401
				Assemblies include pipe and fittings from the roof drains to the discharge points, including supports and other associated work.
			D204002	ROOF DRAINS	EA	EA	Number of roof drains	080402
				Assemblies include roof drains. The unit of measure at the assembly level is number of drains.
			D204003	RAINWATER DRAINAGE EQUIPMENT	EA	EA	Pieces of equipment	080503
				This is equipment associated with the rain water drainage, including fittings and specialties required for hook-up. Assemblies include pumps and other associated items for drainage of rain water.
			D204004	INSULATION & IDENTIFICATION	LF	M	Length of pipe insulation	080403
				Assemblies include insulation used in association with rain water drainage system.
			D204090	OTHER RAIN WATER DRAINAGE SYSTEM	XX	XX		08049X
				Rain water drainage system not described by the assembly categories listed above.
		D2090	OTHER PLUMBING SYSTEMS		EA	EA	Number of special fixtures, etc.	0806
				This subsystem includes all special plumbing systems which are not included in D2010 through D2040.
			D209001	SPECIAL PIPING SYSTEMS	EA	EA	Number of special fixtures, interceptors, etc.	080601
				Assemblies include all special pipe and fittings, excluding acid waste pipe and work with regard to special pipe. Medical gas and vacuum fittings, and associated systems piping are included in this category. The unit of measure at the assembly level is the number of special fixtures, interceptors, outlets, or systems.
			D209002	ACID WASTE SYSTEMS	EA	EA	Number of special fixtures, interceptors, etc.	080602
				Assemblies include all pipe, fittings, special acid waste equipment, and other associated work items with regard to acid waste systems. The unit of measure at the assembly level is the number of special fixtures, interceptors, outlets, or systems.
			D209003	INTERCEPTORS	EA	EA	Number of interceptors	080603
				Assemblies include all interceptors. The unit of measure at the assembly level is number of interceptors.
			D209004	POOL PIPING AND EQUIPMENT	GPM	M3/S	Gallons per minute	080604
				Assemblies include pumps and associated equipment with pools, including specialties required for hook-up. The unit of measure at the assembly level is each.
			D209005	COMPRESSED AIR SYSTEM (NON-BREATHING)	PSI	KGM2	Pounds per square inch
			D209090	OTHER SPECIAL PLUMBING SYSTEMS	XX	XX		08069X
				This system includes special plumbing systems not described by the assembly categories listed above, such as fountain piping systems and devices.
	D30	HVAC			MBH	KW	Total MBH capacity	09
				This system includes all equipment, distribution systems, controls, and energy supply systems required by the heating, ventilating, and air conditioning system.
		D3010	ENERGY SUPPLY		MBH	KW	Total power of heating system	0901
				The energy input to the facility (other than electrical) in the form of fuels or hot and cold water distributed from a central base facility. Energy received from wind or solar power is included in this subsystem.
			D301001	OIL SUPPLY SYSTEM	MBH	KW	Calories per gallon	090101
				Assemblies include storage equipment, transfer equipment, and distribution piping. The unit of measure at the assembly level is each system.
			D301002	GAS SUPPLY SYSTEM	MBH	KW	MBH	090102
				This category includes both natural gas and LPG. Assemblies include metering and regulation equipment, storage equipment, transfer equipment, and distribution piping. The unit of measure at the assembly level is each system.
			D301003	STEAM SUPPLY SYSTEM (FROM CENTRAL PLANT)	MBH	KW	Power	090104
				Assemblies include meters, valves, heat exchangers, fittings, and specialties required for hook-up and distribution piping, including supports, sleeves, and insulation. The unit of measure at the assembly level is each system.
			D301004	HOT WATER SUPPLY SYSTEM (FROM CENTRAL PLANT)	MBH	KW	Power	090105
				Assemblies include meters, valves, heat exchangers, fittings, and specialties required for hook-up and distribution piping, including supports, sleeves, and insulation. The unit of measure at the assembly level is each system.
			D301005	SOLAR ENERGY SUPPLY SYSTEMS	EA	EA	Each System	090106
				Assemblies include collector panels, heat exchangers, storage tanks, pumps, etc., including pipe and fittings required for hook-up. The unit of measure at the assembly level is each system.
			D301006	WIND ENERGY SUPPLY SYSTEM	EA	EA	Each System	090107
				Wind is used to turn a generator which generates electricity. This energy is either stored in a battery or used to generate hot water in an electric boiler. Assemblies would include the required devices to make this a total electromechanical system. The unit of measure at the assembly level is each system.
			D301007	COAL SUPPLY SYSTEM	MBH	KW	Power	090103
				This category includes storage equipment, transfer equipment, processing equipment, and distribution piping. The unit of measure at the assembly level is each system.
			D301090	OTHER ENERGY SUPPLY	XX	XX		09019X
				Energy supply not described by the assembly categories listed above.
		D3020	HEAT GENERATING SYSTEMS		MBH	KW	Total power of heating system	0902
				This subsystem includes steam, hot water, furnace, and unit heater systems. Fuels include coal, oil, gas and electric unless otherwise noted.
			D302001	BOILERS	MBH	KW	Power	090202
				Assemblies include steam or hot water boilers, expansion tanks, chemical feeders, air separators, pumps, heat exchangers, boiler feed units, etc. This assembly would also include fittings and specialties and the flue stack. The unit of measure at the assembly level is each system.
			D302002	FURNACES	MBH	KW	Power	090203
				This is a system that heats air. Assemblies would include furnace and necessary fittings and specialties required for hook-up, including flue and stack. The unit of measure at the assembly level is each.
			D302003	FUEL-FIRED UNIT HEATERS	MBH	KW	Power	090204
				Assemblies would include unit heaters and the energy supply system hook-up (other than electrical), including all necessary pipe, fittings, and specialties required for hook-up. Flue and stack, if required, are included in this assembly. The unit of measure at the assembly level is each.
			D302004	AUXILIARY EQUIPMENT	MBH	KW	Power	090205
				Assemblies would include any other equipment associated with heat generating systems. The unit of measure at the assembly level is each.
			D302005	EQUIPMENT THERMAL INSULATION	SF	M2	Area of insulation	090206
				Assemblies would include insulation of any component in this subsystem. The unit of measure at the assembly level is each.
			D302090	OTHER HEAT GENERATING SYSTEMS	XX	XX		09029X
				Heat generating systems not described in the assembly categories listed above.
		D3030	COOLING GENERATING SYSTEMS		TON	KW	Total power of cooling capacity	0903
				Cooling generating equipment of the absorption, centrifugal, reciprocating, and direct expansion types.
			D303001	CHILLED WATER SYSTEMS	TON	KW	Power	090301
				Assemblies include condensers, compressors, chillers, pumps, cooling towers, etc., including fittings and specialties required for hook-up. The unit of measure at the assembly level is each.
			D303002	DIRECT EXPANSION SYSTEMS	TON	KW	Power	090302
				Assemblies include condensers, compressors, heat pumps, and refrigerant piping. The unit of measure at the assembly level is each.
			D303090	OTHER COOLING GENERATING SYSTEMS	XX	XX		09039X
				Cooling generating systems not described by the assembly categories listed above.
		D3040	DISTRIBUTION SYSTEMS		MBH	KW	Power	0904
				This includes systems that distribute heated and cooled air, ventilating and exhaust air, hot and chilled water, steam, and glycol heating.
			D304001	AIR DISTRIBUTION, HEATING & COOLING	MCFM	L/S	Volume of air flow	090401
				Assemblies include heating coils, cooling coils, and fittings and specialties required for water hook-up. This assembly also includes duct heaters, filters, humidifiers, supply and return ductwork, dampers, fire dampers, supply and return grilles, registers and diffusers, turning vanes, sound traps, and all associated insulation. The unit of measure at the assembly level is MCFM.
			D304002	STEAM DISTRIBUTION SYSTEMS	MBH	KW	Power	090402
				Assemblies include pipe and fittings, supports, wall and floor sleeves, and pipe insulation. The unit of measure at the assembly level is MBH.
			D304003	HOT WATER DISTRIBUTION SYSTEMS	MBH	KW	Power	090403
				Assemblies include pipe and fittings, supports, wall and floor sleeves, and pipe insulation. The unit of measure at the assembly level is MBH.
			D304004	CHANGE OVER DISTRIBUTION SYSTEMS	MBH	KW	Power	090404
			D304005	GLYCOL DISTRIBUTION SYSTEMS	MBH	KW	Power	090405
				Assemblies include pipe and fittings, supports, wall and floor sleeves, and pipe insulation. The unit of measure at the assembly level is MBH.
			D304006	CHILLED WATER DISTRIBUTION SYSTEMS	TON	KW	Power	090406
				Assemblies include pipe and fittings, supports, wall and floor sleeves, and pipe insulation. The unit of measure at the assembly level is tons.
			D304007	EXHAUST SYSTEMS	MCF	L/S	Volume of air flow	090407
				Assemblies include ductwork grilles, registers, diffusers, fans, and all associated work. The unit of measure at the assembly level is each system.
			D304008	AIR HANDLING UNITS	MCFM	L/S	Volume of air flow
			D304090	OTHER DISTRIBUTION SYSTEMS	XX	XX		09049X
				Distribution systems not described by the assembly categories listed above.
		D3050	TERMINAL & PACKAGE UNITS		MBH	KW	Power	0905
				This category includes self-contained heating and cooling units.
			D305001	UNIT VENTILATORS	EA	EA	Number of units	090501
				Assemblies include the complete terminal unit and wall sleeve with all controls.
			D305002	UNIT HEATERS	EA	EA	Number of units	090502
				Assemblies include the complete terminal unit and wall sleeve with all controls.
			D305003	FAN COIL UNITS	EA	EA	Number of units	090503
				Assemblies include the complete terminal unit and wall sleeve with all controls.
			D305004	FIN TUBE RADIATION	EA	EA	Number of units	090504
				Assemblies include the complete terminal unit and wall sleeve with all controls.
			D305005	ELECTRIC HEATING	EA	EA	Number of units	090505
				Assemblies include the complete terminal unit and wall sleeve with all controls.
			D305006	PACKAGE UNITS	EA	EA	Number of units	090505
				Assemblies include complete package units, with integral roof top curbs and all associated devices. A heating system can be selected from hot water, steam coil, or gas furnace and can be a single or multi-zone system. The unit of measure at the assembly level is each.
			D305090	OTHER TERMINAL & PACKAGE UNITS	XX	XX		09059X
				Terminal and package units not described by the assembly categories listed above.
		D3060	CONTROLS & INSTRUMENTATION		MBH	KW	Power	0906
				Includes devices such as thermostats, timers, sensors, control valves, etc., necessary to operate the system as designed.
			D306001	HVAC CONTROLS	EA	EA	Power	090601
				Includes devices such as thermostats, timers, sensors, control valves, etc., necessary to operate the total system. The unit of measure at the assembly level is each system.
			D306002	ELECTRONIC CONTROLS	EA	EA	Number of devices
			D306003	PNEUMATIC CONTROLS	EA	EA	Number of devices
				Assemblies includes ball and butterfly valves, actuators, high pressure chokes, valve positioners, sensors, regulators, etc.
			D306004	INSTRUMENT AIR COMPRESSORS	EA	EA	Number of compressors	090603
				Assemblies include air compressors, dryers, and distribution tubing, (only used with pneumatic control systems). The unit of measure at the assembly level is each.
			D306005	GAS PURGING SYSTEMS	EA	EA	Number of systems	090604
				Assemblies include the removal of contaminated or unwanted gases from a structure or pipe.
			D306090	OTHER CONTROLS INSTRUMENTATION	XX	XX		09069X
				Controls and instrumentation not described by the assembly categories listed above.
		D3070	SYSTEMS TESTING & BALANCING		MBH	KW	Power	0907
				This includes operation of all systems to determine capacity and adjustment of water flow in chilled water and hot water systems, air flow of air handling units, supply and exhaust fans, and supply and return, and exhaust registers.
			D307001	WATER SIDE TESTING & BALANCING - HEATING & COOLING	EA	EA	Number of devices	090701
				Includes operating and testing of pumps, setting of all control valves, and determining system capacity. The unit of measure at the assembly level is each device, i.e., boiler, chiller, fan coil, and unit heater.
			D307002	AIR SIDE TESTING & BALANCING - HEATING, COOLING & EXHAUST	EA	EA	Number of devices	090702
				Includes operating and testing of all air handling devices, adjusting of all fans to set rate of air flow, setting all fan motors at desired operation, setting of air flow at all registers, grilles, diffusers, and louvers to deliver design CFM, and testing and calibrating of thermostats to achieve desired space temperature. The unit of measure at the assembly level is each device.
			D307003	HVAC COMMISSIONING	LS	LS	Lump sum	090703
				Final testing of operational system.
			D307090	OTHER SYSTEMS TESTING & BALANCING	XX	XX		09079X
				Systems testing and balancing not described by the assembly categories listed above.
		D3090	OTHER HVAC SYSTEMS AND EQUIPMENT		EA	EA	Number of special mechanical systems	0908
				This subsystem includes special mechanical systems that are not normally included as part of standard HVAC systems.
			D309001	GENERAL CONSTRUCTION ITEMS	SF	M2	Area of special system	090801
				Includes construction work other than mechanical which must be performed in conjunction with the special mechanical system to make the system complete.
			D309002	REFRIGERATION SYSTEMS	TON	KW	Power	090802
				Includes equipment for refrigeration in a cold storage facility. Both low and medium temperature equipment are included. Assemblies include: condensing and compressor units, evaporator blowers, refrigerant piping, and specialties, heat recovery systems (liquid or gas), heat recovery distribution systems (liquid or gas), and system testing and balancing.
			D309090	OTHER SPECIAL MECHANICAL SYSTEMS	XX	XX		09089X
				Any other mechanical system not defined in other categories. Assemblies would include special systems and special devices. The unit of measure at the assembly level is each system or device.
	D40	FIRE PROTECTION			SF	M2	Gross floor area	10
				This system includes standard and special fire protection systems. Fire alarm systems are included in D503001.
		D4010	FIRE ALARM AND DETECTION SYSTEMS		SF	M2	Gross floor area	1001
				Assemblies include wire, conduit, conduit support or fastening systems, fire alarm devices, fire detection devices, safety switches, mass notification, all electrical connections and other associated items.
			D401001	FIRE ALARM DISTRIBUTION	SF	M2	Gross floor area	100201
				Wire, conduit, conduit support or fastening systems, switches and connections.
			D401002	FIRE ALARM DEVICES	EA	EA	Number of devices	100101
				Fire alarm and fire detection devices
		D4020	FIRE SUPPRESSION WATER SUPPLY AND EQUIPMENT		LF	M	Length of system	190104
				Requirements for water supply design criteria and any items located upstream of the suppression systems such as PIV's, backflow preventers, strainers, etc. The water supply distribution system begins 5'-0" outside the building.
			D402001	FIRE PROTECTION WATER PIPING AND EQUIPMENT	LF	M	Length of system	190104
				Piping
			D402002	FIRE PUMP	EA	EA	Number of pumps
		D4030	STANDPIPE SYSTEMS		EA	EA	Number of sprinkler heads	1003
				This subsystem includes the complete standpipe system.
			D403001	STANDPIPE EQUIPMENT & PIPING	EA	EA	Number of sprinkler heads	100301
				Assemblies include standpipe risers and all other piping, fittings, and supports associated with this category. Siamese connections, roof manifolds, cabinets, hoses, racks, and other fire department connections are included in this assembly. All equipment including pumps, tanks, etc., with all required fittings and specialties for hook-up are included in this assembly.
		D4040	SPRINKLERS		EA	EA	Number of sprinkler heads	1001
				This subsystem includes the water supply equipment and related piping from the equipment to the sprinkler head.
			D404001	SPRINKLERS AND RELEASING DEVICES	EA	EA	Number of sprinkler heads	100201
				The fixture, device, or sprinkler head that releases the water to suppress the fire. The unit of measure at the assembly level is each sprinkler head.
			D404002	SPRINKLER WATER SUPPLY EQUIPMENT AND PIPING	EA	EA	Number of sprinkler heads	100101
				Assemblies include alarm valves, flow control valves, pipe and fittings from equipment to sprinkler heads, including all supports and wall or floor sleeves. All equipment including tanks, pumps, and other associated equipment, fittings and specialties required for hook-up are in this assembly. The unit of measure at the assembly level is each sprinkler head.
		D4050	FIRE PROTECTION SPECIALTIES		EA	EA	Number of extinguishers	1004
				This subsystem includes fire extinguishing devices.
			D405001	PORTABLE EXTINGUISHERS	EA	EA	Number of extinguishers	100401
				Assemblies include all types of fire extinguishers, i.e., water, dry chemical, carbon dioxide, soda acid, etc. The brackets, sleeves, and supporting devices are included in this assembly.
		D4090	OTHER FIRE PROTECTION SYSTEMS		EA	EA	Each system	1005
				Requirements for all other suppression systems. Water based systems (e.g., foam systems) specified from water supply onwards, complete specification for gas systems, incidental systems such as kitchen hood systems.
			D409001	CARBON DIOXIDE SYSTEMS	EA	EA	Number of systems
			D409002	FOAM GENERATING EQUIPMENT	EA	EA	Pieces of equipment
			D409003	CLEAN AGENT SYSTEMS	EA	EA	Number of systems
			D409004	HOOD & DUCT FIRE PROTECTION	EA	EA	Pieces of equipment
			D409090	OTHER SPECIAL FIRE PROTECTION SYSTEMS	EA	EA	Each system	100501
				Assemblies includes other fire protection systems such as halon systems, exhaust hood systems, and special chemical suppression systems.
	D50	ELECTRICAL			AMP	AMP	Gross floor area	11
				This system is defined by the electric current used or regarded as a source of power.
		D5010	ELECTRICAL SERVICE & DISTRIBUTION		AMP	AMP	Gross floor area	1101
				This subsystem provides for all electrical devices that are required to deliver the main source of power to the facility and to distribute this power to subpanels.
			D501001	MAIN TRANSFORMERS	AMP	AMP	Number of transformers	110101
				Transformers used for primary electrical service and located within the building footprint. Assemblies include transformers, raised pad, trenching, and backfill. This assembly will not likely be used when an exterior transformer is required in G4010 ELECTRICAL DISTRIBUTION.
			D501002	SERVICE ENTRANCE EQUIPMENT	AMP	AMP	Gross floor area	110103
				This includes the protection equipment and metering devices for main distribution. Assemblies include main distribution panel, breaker, fuses, and meters.
			D501003	INTERIOR DISTRIBUTION TRANSFORMERS	AMP	AMP	Gross floor area	110104
				Transformers fed downstream of the service entrance equipment. Assemblies include transformers, conduit, conduit support, and wire.
			D501004	PANELBOARDS	AMP	AMP	Gross floor area	110105
				Branch circuit panelboards. Assemblies include panelboards, breakers ,conduit, and wire.
			D501005	ENCLOSED CIRCUIT BREAKERS	AMP	AMP	Gross floor area	110106
				Over-current protection device enclosed in its own housing. Assemblies include enclosed circuit breaker, conduit, and wire.
			D501006	MOTOR CONTROL CENTERS	AMP	AMP	Gross floor area	110107
				This is a cabinet in which motor starters and operation devices are contained. Assemblies include the motor control center cabinet, motor starters, contacts, switches, conduit, wire, and all associated items.
			D501090	OTHER SERVICE AND DISTRIBUTION	XX	XX		11019X
				Service and distribution not described by the assembly categories listed above.
		D5020	LIGHTING & BRANCH WIRING		SF	M2	Floor area	1102
				Lighting systems including light fixtures and devices, i.e., switches, receptacles, and equipment connections.
			D502001	BRANCH WIRING	SF	M2	Floor area	110201
				This assembly includes switches, receptacles, equipment connections, conduit, and wire.
			D502002	LIGHTING EQUIPMENT	SF	M2	Floor area	110202
				This assembly includes fixtures, conduit, wire, and switching devices.
			D502090	OTHER LIGHTING AND BRANCH WIRING	XX	XX		11029X
				Lighting and branch wiring not described by the assembly categories listed above.
		D5030	COMMUNICATIONS & SECURITY		SF	M2	Floor area	1201
				This subsystem includes provisions for communication devices and alarm protection systems.
			D503001	TELECOMMUNICATIONS SYSTEMS	EA	EA	Number of outlets	120103
				This system would include central switchboards, telephone sets, underground ducts, and manholes. Assemblies include wire, conduit, backboards, cabinets, outlets, and power supply connections.
			D503002	PUBLIC ADDRESS SYSTEMS	SF	M2	Floor area	120104
				Assemblies include wire, conduit, speakers, monitoring devices, amplifiers, switches, power system tie-in devices, and detection devices.
			D503003	INTERCOMMUNICATIONS SYSTEMS	EA	EA	Number of stations	120105
				Assemblies include wire, conduit, speakers, monitoring devices, amplifiers, switches, power system tie-in devices, and detection devices.
			D503004	TELEVISION SYSTEMS	EA	EA	Number of outlets	120107
				Assemblies include wire, conduit, grounding amplifiers, receivers, video equipment, and outlets grouped according to use.
			D503005	SECURITY SYSTEMS	EA	EA	Number of system control panels	120108
				Assemblies include wire, conduit, conduit support or fastening systems, security alarm devices, all electrical connections, and other associated items. Intrusion Detection Systems (IDS) are included in this category.
			D503006	NURSE CALL SYSTEMS	EA	EA	Number of outlets	120102
				Assemblies include wire, conduit, speakers, monitoring devices, amplifiers, switches, power system tie-in devices, and detection devices.
			D503007	CLOCK & PROGRAM SYSTEMS	EA	EA	Number of clocks	120106
				Assemblies include wire, conduit, power systems tie-in, safety switches, control panels, battery back-up devices, clocks and outlets.
			D503090	OTHER COMMUNICATIONS & ALARM SYSTEMS	XX	XX		12019X
				Communication and alarm systems not described by the assembly categories listed above.
		D5090	OTHER ELECTRICAL SERVICES		SF	M2	Gross Floor area	1202
				Systems not described in System D5030.
			D509001	GENERAL CONSTRUCTION ITEMS (ELECTRICAL)	SF	M2	Gross Floor area	120201
				Includes construction other than electrical which must be performed in conjunction with the special electrical system to make the system complete.
			D509002	EMERGENCY LIGHTING & POWER	SF	M2	Gross Floor area	120202
				Assemblies include fixtures, motors used for power generation, connection and testing, transfer switches, conduit, wire, battery chargers, batteries, and solar panels.
			D509003	GROUNDING SYSTEMS	SF	M2	Gross Floor area	120203
				This assembly includes grounding protection systems.
			D509004	LIGHTNING PROTECTION	SF	M2	Gross Floor area	120204
				Assemblies include lightning protection devices (air terminals, mounting devices), clamps, ground rods, cadwells, conductors, trenching, backfill, and any other items used to ground metal structural frames with conduit and wire.
			D509005	ELECTRIC HEATING	SF	M2	Gross Floor area	120205
				Items could include baseboard heaters and wall and ceiling heaters. Assemblies include safety switches, control devices, heaters, conduit, and wire.
			D509006	ENERGY MANAGEMENT CONTROL SYSTEM	SF	M2	Gross Floor area	120206
				Assemblies include wire, conduit, conduit support or fastening systems, sensor devices, and all electrical connections.
			D509090	OTHER SPECIAL SYSTEMS AND DEVICES	XX	XX		12029X
				Special systems and devices not described by the assembly categories listed above.

Section E - Equipment & Furnishings

Unf L1	Unf L2	Unf L3	WBS L4	Definition	E UOM	M UOM	Quantity Definition	WBS Ref No
E	EQUIPMENT & FURNISHINGS				SF	M2	Gross Floor Area
				The types of equipment included in this assembly consist of the following: commercial, institutional, and vehicular. The types of furnishings found here include artwork, window treatments, seating, furniture, rugs etc.
	E10	EQUIPMENT			SF	M2	Gross Floor area	13
				This system refers to equipment not found in System C1030 (Fittings).
		E1010	COMMERCIAL EQUIPMENT		SF	M2	Floor area	1301
				This equipment is not likely to be used in every building type. Subsystem C1030 includes those items likely to be found in every building type.
			E101001	CHECKROOM EQUIPMENT	EA	EA	Number of coat hanging devices	130102
				All associated work items including keys, tags, and storage cabinets would be included in this assembly.
			E101002	REGISTRATION EQUIPMENT	EA	EA	Pieces of equipment	130114
			E101003	VENDING EQUIPMENT	EA	EA	Pieces of equipment	130104
			E101004	LAUNDRY EQUIPMENT	EA	EA	Pieces of equipment	130116
			E101005	SECURITY & VAULT EQUIPMENT	EA	EA	Pieces of equipment	130117
			E101006	TELLER AND SERVICE EQUIPMENT	EA	EA	Pieces of equipment
			E101007	MERCANTILE EQUIPMENT	EA	EA	Pieces of equipment
			E101008	OFFICE EQUIPMENT	EA	EA	Pieces of equipment
		E1020	INSTITUTIONAL EQUIPMENT		SF	M2	Floor area
				Institutional equipment includes items that are normally found in hospitals, laboratories, auditoriums, and libraries.
			E102001	MISCELLANEOUS COMMON FIXED & MOVEABLE EQUIPMENT	EA	EA	Pieces of equipment	130108
			E102002	MEDICAL EQUIPMENT	EA	EA	Pieces of equipment	130110
			E102003	LABORATORY EQUIPMENT	EA	EA	Pieces of equipment	130111
			E102004	MORTUARY EQUIPMENT	EA	EA	Pieces of equipment	130112
			E102005	AUDITORIUM & STAGE EQUIPMENT	EA	EA	Pieces of equipment	130113
			E102006	LIBRARY EQUIPMENT	EA	EA	Pieces of equipment	130115
			E102007	ECCLESIASTICAL EQUIPMENT	EA	EA	Pieces of equipment
			E102008	INSTRUMENTAL EQUIPMENT	EA	EA	Pieces of equipment
			E102009	AUDIO-VISUAL EQUIPMENT	EA	EA	Pieces of equipment
			E102010	DETENTION EQUIPMENT	EA	EA	Pieces of equipment
		E1030	VEHICULAR EQUIPMENT		EA	EA	Pieces of equipment
				Vehicular equipment includes for parking, loading docks, and warehouses.
			E103001	PARKING CONTROL EQUIPMENT	EA	EA	Pieces of equipment	130107
			E103002	LOADING DOCK EQUIPMENT	EA	EA	Number of docks	130106
			E103003	WAREHOUSE EQUIPMENT	EA	EA	Pieces of equipment	130109
			E103004	AUTOMOTIVE SHOP EQUIPMENT	EA	EA	Pieces of equipment	0
		E1040	GOVERNMENT FURNISHED EQUIPMENT		EA	EA	Pieces of equipment
				New and existing equipment provided to the Contractor by the Government.
		E1090	OTHER EQUIPMENT
				The type of equipment found in his category include items for maintenance, food service, and waste handling.
			E109001	BUILT-IN MAINTENANCE EQUIPMENT	SF	M2	Floor area	130101
				The unit of measure at the assembly level is each.
			E109002	FOOD SERVICE EQUIPMENT	EA	EA	Seating capacity	130103
				The unit of measure at the assembly level is the total set of equipment needed in the particular functional space area.
			E109003	WASTE HANDLING EQUIPMENT	EA	EA	Pieces of equipment	130105
			E109004	RESIDENTIAL EQUIPMENT	EA	EA	Pieces of equipment
			E109005	UNIT KITCHENS	EA	EA	Pieces of equipment
			E109006	DARKROOM EQUIPMENT	EA	EA	Pieces of equipment
			E109007	ATHLETIC, RECREATIONAL, & THERAPEUTIC EQUIPMENT	EA	EA	Pieces of equipment
			E109008	PLANETARIUM EQUIPMENT	EA	EA	Pieces of equipment
			E109009	OBSERVATORY EQUIPMENT	EA	EA	Pieces of equipment
			E109010	AGRICULTURAL EQUIPMENT	EA	EA	Pieces of equipment
			E109090	OTHER SPECIALIZED FIXED AND MOVEABLE EQUIPMENT	XX	XX		13019X
				Specialized fixed and moveable equipment not described by the assembly categories listed above.
	E20	FURNISHINGS			SF	M2	Floor area	14
				The types of furnishings found here include artwork, window treatments, seating, furniture, rugs, etc.
		E2010	FIXED FURNISHINGS		SF	M2	Floor area	1401
				The types of furnishings found here include artwork, window treatments, and seating.
			E201001	FIXED ARTWORK	EA	EA	Pieces of art work	140102
			E201002	WINDOW TREATMENTS	SF	M2	Area of window treatment	140103
			E201003	SEATING (FIXED)	EA	EA	Number of seats	140104
			E201004	FIXED INTERIOR LANDSCAPING	EA	EA	Number of items
			E201090	OTHER FIXED INTERIOR FURNISHINGS	EA	EA	Number of furnishings	14019X
		E2020	MOVEABLE FURNISHINGS
				The types of furnishings found here include moveable artwork, furniture, rugs, etc.
			E202001	MOVEABLE ART WORK	EA	EA	Pieces of art work
			E202002	MODULAR PREFABRICATED FURNITURE	SF	M2	Pieces of prefabricated furniture	140101
			E202003	FREESTANDING FURNITURE	EA	EA	Pieces of furniture
			E202004	RUGS & ACCESSORIES	EA	EA	Number of rugs, mats, accessories	140105
				Assemblies include rugs and accessories.
			E202005	MOVEABLE MULTIPLE SEATING	EA	EA	Number of items
			E202006	MOVEABLE INTERIOR LANDSCAPING	EA	EA	Number of items
			E202090	OTHER MOVEABLE FURNISHINGS	EA	EA	Number of furnishings

Section F - Special Construction & Demolition

Unf L1	Unf L2	Unf L3	WBS L4	Definition	E UOM	M UOM	Quantity Definition	WBS Ref No
F	SPECIAL CONSTRUCTION & DEMOLITION				SF	M2	Floor area
				Special construction includes air-supported structures; pre-engineered structures; special purpose rooms; sound, vibration, and seismic construction; radiation protection; special security systems; aquatic facilities; ice rinks, site constructed incinerators; kennels and animal shelters; liquid and gas storage tanks; recording instrumentation; and building automation systems. Selective building demolition includes demolition of existing buildings, and site demolition.
	F10	SPECIAL CONSTRUCTION			SF	M2	Floor area	15
				Special construction includes air-supported structures; pre-engineered structures; special purpose rooms; sound, vibration, and seismic construction; radiation protection; special security systems; aquatic facilities; ice rinks, site constructed incinerators; kennels and animal shelters; liquid and gas storage tanks; recording instrumentation; and building automation systems.
		F1010	SPECIAL STRUCTURES		SF	M2	Floor area
				Special structures includes air-supported structures, and pre-engineered structures.
			F101001	METAL BUILDING SYSTEMS	SF	M2	Floor area	1504
			F101002	EXTERIOR UTILITY BUILDINGS	SF	M2	Floor area of exterior building	1506
			F101003	AIR-SUPPORTED STRUCTURES	SF	M2	Floor area of exterior building
			F101090	OTHER SPECIAL CONSTRUCTION	XX	XX
		F1020	INTEGRATED CONSTRUCTION		SF	M2	Floor area
				Integrated construction includes integrated assemblies and special purpose rooms.
			F102001	SPECIAL PURPOSE ROOMS	SF	M2	Area of room	1503
			F102002	INTEGRATED ASSEMBLIES	SF	M2	Area of room
			F102090	OTHER INTEGRATED CONSTRUCTION	SF	M2	Area of room
		F1030	SPECIAL CONSTRUCTION SYSTEMS		SF	M2	Area of room
				Special construction systems includes sound, vibration, and seismic construction; radiation protection; special security systems; and built-in place vaults.
			F103001	VAULTS	SF	M2	Area of vault	1501
				This is a built-in-place vault. Prefabricated safes are not included in this assembly. The unit of measure at the assembly level is each.
			F103002	SOUND, VIBRATION, AND SEISMIC CONSTRUCTION	SF	M2	Area of room
			F103003	RADIATION PROTECTION	SF	M2	Area of room
			F103090	OTHER SPECIAL CONSTRUCTION SYSTEMS	SF	M2	Area of room
		F1040	SPECIAL FACILITIES		SF	M2	Area of room
				Special facilities includes aquatic facilities; ice rinks, site constructed incinerators; kennels and animal shelters; and liquid and gas storage tanks.
			F104001	INTERIOR SWIMMING POOLS	SF	M2	Area of pool	1502
			F104002	LIQUID AND GAS STORAGE TANKS	EA	EA	Number of storage tanks
			F104003	KENNELS AND ANIMAL SHELTERS	SF	M2	Area of kennel or animal shelter
			F104004	SITE CONSTRUCTED INCINERATORS	EA	EA	Number of incinerators
			F104005	ICE RINKS	SF	M2	Area of ice rink
			F104090	OTHER SPECIAL FACILITIES	EA	EA	Number of special facilities
		F1050	SPECIAL CONTROLS AND INSTRUMENTATION		XX	XX
				Special controls and instrumentation includes recording instrumentation and building automation systems.
			F105001	RECORDING INSTRUMENTATION	EA	EA	Number of instruments
			F105002	BUILDING AUTOMATION SYSTEMS	EA	EA	Number of systems
			F105090	OTHER SPECIAL CONTROLS AND INSTRUMENTATION	EA	EA	Number of controls and instruments
	F20	SELECTIVE BUILDING DEMOLITION			LS	LS		16
				Selective building demolition includes demolition of existing buildings, site demolition, and hazardous components abatement.
		F2010	BUILDING ELEMENTS DEMOLITION		LS	LS		1601
				Selective building demolition includes demolition of existing buildings, and site demolition.
			F201001	SUBSTRUCTURE & SUPERSTRUCTURE	LS	LS		160101
			F201002	EXTERIOR CLOSURE	LS	LS		160102
			F201003	ROOFING	LS	LS		160103
			F201004	INTERIOR CONSTRUCTION & FINISHES	LS	LS		160104
			F201005	CONVEYING SYSTEMS	LS	LS		160105
			F201006	MECHANICAL SYSTEMS	LS	LS		160106
			F201007	ELECTRICAL SYSTEMS	LS	LS		160107
			F201008	EQUIPMENT & FURNISHINGS	LS	LS		160108
			F201090	OTHER NON-HAZARDOUS SELECTIVE BUILDING DEMOLITION	XX	XX		16019X
				Non-hazardous selective building demolition not described by the assembly categories listed above.
		F2020	HAZARDOUS COMPONENTS ABATEMENT		LS	LS		1602
				Hazardous components abatement includes the removal or encapsulation of hazardous building materials and components. Hazardous components include asbestos, lead based paint, paint containing cadmium, chromium and lead, mercury and low level radioactive components, PCBs, ozone depleting substances, animal droppings and molds and spores.
			F202001	SUBSTRUCTURE & SUPERSTRUCTURE	LS	LS		160201
			F202002	EXTERIOR CLOSURE	LS	LS		160202
			F202003	ROOFING	LS	LS		160203
			F202004	INTERIOR CONSTRUCTION & FINISHES	LS	LS		160204
			F202005	CONVEYING SYSTEMS	LS	LS		160205
			F202006	MECHANICAL SYSTEMS	LS	LS		160206
			F202007	ELECTRICAL SYSTEMS	LS	LS		160207
			F202008	EQUIPMENT & FURNISHINGS	LS	LS		160208
			F202090	OTHER HAZARDOUS SELECTIVE BUILDING DEMOLITION	XX	XX		16029X
				Hazardous selective building demolition not described by the assembly categories listed above.

Section G - Building Sitework

Unf L1	Unf L2	Unf L3	WBS L4	Definition	E UOM	M UOM	Quantity Definition	WBS Ref No
G	BUILDING SITEWORK				ACR	Hectare	Total area of site
				Building sitework includes site preparations, site improvements, site civil/mechanical utilities, site electrical utilities, service and pedestrian tunnels, and other site construction, such as bridges, and railroad spurs.
	G10	SITE PREPARATIONS			ACR	Hectare	Total area of site	17
				This system includes assemblies for miscellaneous sitework such as clearing and grubbing, demolition and relocation, various earthwork tasks, and other site preparation and cleanup requirements. Hazardous cleanup is not included but is the subject of another WBS.
		G1010	SITE CLEARING		ACR	Hectare	Area to be cleared	1701
				This covers the different assemblies and options available for clearing of a site, tree and stump removal, burning, grubbing, chipping, and load and haul assemblies for removal of the cleared material.
			G101001	CLEARING	ACR	Hectare	Area to be cleared	170101
				This is the removal of above ground vegetation including stumps. For a wet site, Low Ground Pressure (LGP) equipment is used.
			G101002	TREE REMOVAL	EA	EA	Number of trees to be removed	170102
				This is the selective removal of trees on the site. Various options exist for different sizes of trees to be removed.
			G101003	STUMP REMOVAL	EA	EA	Number of stumps to be removed	170103
				This is the selective removal of stumps on the site. Various options exist for different sizes of stumps to be removed.
			G101004	GRUBBING	ACR	Hectare	Area to be grubbed	170105
				Grubbing is the removal of sod and other topsoil that contains unsuitable organic material. Various equipment types and size choices are available. Wet grubbing utilizes Low Ground Pressure (LGP) equipment. Haul-off of grubbed material is also included.
			G101005	SELECTIVE THINNING	ACR	Hectare	Area to be thinned	170106
				This is the selective removal of trees and underbrush without requiring extensive clearing and/or grubbing of the site.
			G101006	DEBRIS DISPOSAL	CY	M3	Volume of material	170107
				This is the disposal of the material that has been cleared and grubbed. Loading, hauling, and dump charges are included.
			G101090	OTHER SITE CLEARING	XX	XX		17019X
				Site clearing not described by the assembly categories listed above.
		G1020	SITE DEMOLITION & RELOCATIONS		SY	M2	Area to be demolished	1702
				This includes the demolition and/or relocation of structures, pavements, fencing, and underground utilities. Disposal of debris or demolished material, including loading and hauling, is also included.
			G102001	BUILDING MASS DEMOLITION	CF	M3	Interior volume of building	170201
				This is the complete demolition of buildings or structures. Options include steel, concrete, masonry, and wood structures.
			G102002	ABOVE GROUND SITE DEMOLITION	SY	M2	Area to be demolished	170202
				This is the demolition of pavements, fencing, and other non-building structures on a site. Pavement include roads, sidewalks, driveways, and curbs. Fencing types include chain link, barbed wire, and wood. This can also include removal and disposal of above ground storage tanks, including tank contents, associated piping, etc.
			G102003	UNDERGROUND SITE DEMOLITION	SY	M2	Area to be demolished	170203
				This is the demolition of underground utilities such as piping, manholes, and other non-building underground structures. The unit of measure at the assembly level for piping is LF and for manholes is CY. This can also include removal and disposal of under ground storage tanks, including tank contents, associated piping, etc.
			G102004	BUILDING RELOCATION	SF	M2	Area of building to be relocated	170205
				This is the process of dismantling a structure, and reassembling it on a different site.
			G102005	UTILITY RELOCATION	LF	M	Length of pipe run	170206
				To remove and reset. This is the removal and relocation of underground utilities such as steel and concrete pipe.
			G102006	FENCING RELOCATION	LF	M	Length of fencing	170207
			G102007	SITE CLEANUP	SY	M2	Area of site to clean	170401
				Covered in this assembly category are items for site and area cleanup and pavement sweeping. Disposal of the debris is also included.
			G102090	OTHER SITE DEMOLITION & RELOCATIONS	XX	XX		17029X
				Site demolition and relocation not described by the assembly categories listed above.
		G1030	SITE EARTHWORK		CY	M3	Volume of material	1703
				Included are assemblies and options for site work such as grading, excavation, filling, compaction, stabilization, etc.
			G103001	GRADING	SY	M2	Area to be graded	170301
				Grading is leveling or flattening of the site in preparation for landscaping or other site construction. Includes unlined stormwater collection ponds.
			G103002	COMMON EXCAVATION	CY	M3	Volume of material to be excavated	170302
				This is excavation for roads, sidewalks, curbs, and trenching for underground utilities. Excavation may be carried out by a variety of equipment sizes and types. Disposal of the excavated material is also included.
			G103003	ROCK EXCAVATION	CY	M3	Volume of rock to be excavated	170303
				This is excavation of rock by explosives. Different equipment selections and load and haul are included.
			G103004	FILL & BORROW	CY	M3	Volume of material to place	170304
				This is filling or replacing the material that was removed during excavation. Either the excavated material may be used or soil and sand may be hauled in from off-site. Filling to basements and foundations is not included in the subsystem.
			G103005	COMPACTION	CY	M3	Volume of material to compact	170305
				Compaction is the process of packing the fill material once it is in place. This may be done by machine or hand. Assemblies exist for both hand and machine compaction of soil, sand, and the excavated material.
			G103006	SOIL STABILIZATION	CY	M3	Volume of soil to stabilize	170306
				This is stabilization of the soil-in-place by the addition of lime or cement.
			G103007	SLOPE STABILIZATION	SY	M2	Area of slope	170307
				This is stabilization of the soil-in-place through the use of rip rap, gabions, slope paving, or other forms of soil armoring.
			G103008	SOIL TREATMENT	SY	M2	Area of soil to treat	170308
				Treatment of soil prior to final construction for insect protection or other purposes.
			G103009	SHORING	SF	M2	Area requiring shoring	170309
				Shoring is the temporary support for existing structures or excavation during construction.
			G103010	TEMPORARY DEWATERING	SY	M2	Area to dewater	170310
				This is the dewatering of the site by wellpoints to lower the groundwater table. This will facilitate excavation in areas with high water tables.
			G103011	TEMPORARY EROSION & SEDIMENT CONTROL	SF	M2	Area to be protected	170311
				Interim measures to minimize erosion during construction.
			G103090	OTHER SITE EARTHWORK	XX	XX		17039X
				Site earthwork not described by the assembly categories listed above.
		G1040	HAZARDOUS WASTE REMEDIATION		LS	LS
				Hazardous waste remediation, removal, disaposal and restoration of contaminated soil and/or groundwater.
			G104001	REMOVAL OF CONTAMINATED SOIL	CY	M3	Volume of contaminated soil
			G104002	SOIL RESTORATION AND TREATMENT	CY	M3	Volume of soil
			G104090	OTHER HAZARDOUS WASTE REMEDIATION	XX	XX
				Hazardous waste remediation not described by the assembly categories listed above.
	G20	SITE IMPROVEMENTS			LS	LS		18
				This includes improvements such as parking lots, sidewalks, roadways, fencing, retaining walls, and landscaping.
		G2010	ROADWAYS		SY	M2	Area of roadway	1801
				This subsystem includes options for access, arterial, or interstate roadways. A variety of pavement types and thickness are available.
			G201001	BASES & SUBBASES	SY	M2	Area of roadway	180101
				These are the compacted and prepared gravel or soil layers that are placed prior to the installation of the final surface. The subbase is placed and compacted before the base layer is applied.
			G201002	CURBS & GUTTERS	LF	M	Length of drainage pipe
				This is the drainage system for the selected roadway type. Options include curb and gutter drains or area drains with grates.
			G201003	PAVED SURFACES	SY	M2	Area of roadway	180103
				This is material that is placed atop the base layer to provide the driving surface.
			G201004	MARKING & SIGNAGE	SY	M2	Area of roadway	180104
				This includes roadway signage and pavement painting. Assemblies are included for traffic signs and posts and intersection, crosswalk, or other pavement painting or striping.
			G201005	GUARDRAILS & BARRIERS	LF	M	Length of guardrail or barrier	180105
				This is any associated guardrails or barriers that are required for the selected roadway type.
			G201006	RESURFACING	SY	M2	Area of roadway	180106
				This is the placement of an asphalt wearing course over the existing pavement surface. Assemblies exist for resurfacing of gravel, concrete, and asphalt roadways.
			G201090	OTHER ROADWAYS	XX	XX		18019X
				Roadways not described by the assembly categories listed above.
		G2020	PARKING LOTS		EA	EA	Number of spaces	1802
				These are the areas required of vehicles parking and include different surfaces and drainage options.
			G202001	BASES & SUBBASES	SY	M2	Area of parking lot	180201
				These are the compacted and prepared gravel or soil layers that are placed prior to the installation of the final surface. The subbase is placed and compacted before the base layer is applied.
			G202002	CURBS & GUTTERS	LF	M	Length of curbs & gutters
				This is the curb and gutter drains or area drains with grates.
			G202003	PAVED SURFACES	SY	M2	Area of parking lot	180203
				This is material that is placed atop the base layer to provide the driving surface.
			G202004	MARKING & SIGNAGE	EA	EA	Number of spaces	180205
				This includes painting of the parking stalls, signage, etc.
			G202005	GUARDRAILS & BARRIERS	LF	M	Length of guardrail or barrier	180205
				Guardrails, barriers, parking stops and other similar devices.
			G202006	RESURFACING	SY	M2	Area of parking lot	180206
				This is the placement of an asphalt wearing course over the existing parking surface.
			G202007	MISCELLANEOUS STRUCTURES AND EQUIPMENT	EA	EA	Number of structures or equipment
			G202090	OTHER PARKING LOTS	XX	XX		18029X
				Parking areas not described by the assembly categories listed above.
		G2030	PEDESTRIAN PAVING		SY	M2	Area of pavement	1803
				This subsystem includes options for sidewalks and other small paved areas.
			G203001	BASES & SUBBASES	SY	M2	Area of pavement	180301
				These are the compacted and prepared gravel or soil layers that are placed prior to the installation of the final surface. The subbase is placed and compacted before the base layer is applied.
			G203002	CURBS & GUTTERS	LF	M	Length of curbs & gutters
				This is the curb and gutter drains or area drains with grates.
			G203003	PAVED SURFACES	SY	M2	Area of pavement	180303
				This is material that is placed atop the base layer to provide the walking or driving surface.
			G203004	GUARDRAILS & BARRIERS	LF	M	Length of guardrail or barrier	180304
				This is any associated guardrails or barriers that are required.
			G203005	RESURFACING	SY	M2	Area of pavement	180305
				This is the placement of an asphalt wearing course over the existing pavement surface.
			G203090	OTHER WALKS, STEPS & TERRACES	XX	XX		18039X
				Walks, steps, ramps, terraces not described by the assembly categories listed above.
		G2040	SITE DEVELOPMENT		EA	EA	Each Structure	1804
				Included are assemblies for on-site construction of fences, retaining walls, playing fields, fountains, and other site improvements.
			G204001	FENCING & GATES	LF	M	Length of fence	180401
				This includes installation or construction of security, boundary, or barbed wire fencing and all required gates.
			G204002	RETAINING WALLS AND FREESTANDING WALLS	SY	M2	Area of wall	180402
				These are structures used to prevent the flow or lateral movement of soil. Assemblies exist for cast-in-place concrete retaining walls.
			G204003	EXTERIOR FURNISHINGS	EA	EA	Number of furnishings	180403
				This includes the addition of such exterior furnishings as benches, planters, etc.
			G204004	SECURITY STRUCTURES	EA	EA	Number of security structures	180404
				This includes the construction or addition of security structures such as guard houses.
			G204005	SIGNAGE	EA	EA	Number of signs	180405
				Signs displayed to convey direction or information such as building function or tenant except for signs included in G201004 and G202004.
			G204006	FOUNTAINS & POOLS	EA	EA	Number of fountains or pools	180406
				This includes assemblies for swimming pools and decorative fountains.
			G204007	PLAYING FIELDS	EA	EA	Number of playing fields	180407
				Playing fields such as baseball or tennis courts as well as back stops, bleachers, and other playing field requirements are included.
			G204008	TERRACE AND PERIMETER WALLS	SY	M2	Area of wall
			G204009	FLAGPOLES	EA	EA	Number of flagpoles
			G204090	OTHER SITE IMPROVEMENTS	XX	XX		1804
				This includes any other miscellaneous structures, such as a car wash, banking system, and theatre equipment located on the site.
		G2050	LANDSCAPING		SY	M2	Area to be landscaped	1805
				Assemblies are included that improve the appearance of the site by planting, seeding, and sodding.
			G205001	FINE GRADING & SOIL PREPARATION	SY	M2	Area of site	180501
				Fine grading of the site by hand or machine is required to prepare the soil for planting, seeding, or sodding.
			G205002	EROSION CONTROL MEASURES	SY	M2	Area of erosion	180502
				Soil erosion or deterioration due to wind, rain or other factors can be controlled or remedied in different ways. This includes slope protection by planting or vegetation or grass and/or placement of manmade geotextiles.
			G205003	TOPSOIL & PLANTING BEDS	SY	M2	Area of planting bed	180503
				Topsoil is placed to provide the nutritious soil bed which is required for plants or grass to grow.
			G205004	SEEDING, SPRIGGING AND SODDING	SY	M2	Area of site	180504
				This includes the seeding, sodding, fertilizing, watering, and mowing for the grass required on site.
			G205005	PLANTINGS	EA	EA	Number of plants	180505
				This includes the planting of trees, shrubs, and other vegetation for site beautification or improvement.
			G205006	PLANTERS	EA	EA	Number of planters	180506
				Planters are exterior decorative containers that contain plants or trees.
			G205007	IRRIGATION SYSTEMS	SY	M2	Area of site to be watered	180507
				This includes the installation of underground irrigation systems required for watering of trees, shrubs, and grass or other vegetation.
			G205090	OTHER LANDSCAPING	XX	XX		18059X
				Landscaping not described by the assembly categories listed above.
		G2060	AIRFIELD PAVING		SY	M2	Area of paving
				Aircraft parking apron and runway paving.
			G206001	AIRFIELD PAVING CONSTRUCTION	SY	M2	Area of paving
			G206002	OTHER PAVING	SY	M2	Area of paving
			G206003	JOINTS AND ANCHORAGE	SY	M2	Area of paving
			G206004	NAVIGATION AIDS	LS	LS
			G206005	AIRFIELD MARKINGS	LS	LS
	G30	SITE CIVIL/MECHANICAL UTILITIES			EA	EA	Each utility
				Site mechanical utilities includes water supply, sanitary sewer, storm sewer, heating distribution, cooling distribution, fuel distribution, and other site mechanical utilities, such as industrial waste systems.
		G3010	WATER SUPPLY		LF	M	Length of system	1901
				This includes installation or construction of water distribution systems and facilities.
			G301001	WELL SYSTEMS	EA	EA	Each system	190101
				This includes all the components necessary to install a well, including drilling, installing casings, pumps, valves, etc.
			G301002	POTABLE WATER DISTRIBUTION	LF	M	Length of system	190102
				This includes construction and installation of underground piping, valve boxes, and valves.
			G301003	POTABLE WATER STORAGE	GAL	GAL	Amount stored	190103
				This includes construction and installation of tanks, both at grade and elevated.
			G301004	FIRE PROTECTION WATER DISTRIBUTION	LF	M	Length of system	190104
				This includes construction and installation of dedicated water piping for fire protection system only. This does not include potable water distribution systems that are used as a water source for fire protection systems.
			G301005	FIRE PROTECTION WATER STORAGE	GAL	GAL	Amount stored	190105
				This includes tanks on grade and elevated for storage of water for fire protection only.
			G301006	NON-POTABLE WATER DISTRIBUTION	LF	M	Length of system	190106
				This includes construction and installation of water distribution system not for consumption, such as irrigation or hydro-electric power generation and from reservoirs to treatment facilities.
			G301007	PUMPING STATIONS	GPM	L/S	Operating capacity	190107
				This includes construction and installation of pumps, valves, and piping.
			G301008	PACKAGED WATER TREATMENT PLANTS	GPD	GPD	Operating capacity	190108
				This includes installation of completely assembled water treatment plants.
			G301090	OTHER WATER SUPPLY	XX	XX		19019X
				Water supply not described by the assembly categories listed above.
		G3020	SANITARY SEWER		LF	M	Length of system	1902
				This includes all assemblies necessary for sewage collection systems.
			G302001	SANITARY SEWER PIPING	LF	M	Length of piping	190201
				This includes installation of piping for collection of sewage.
			G302002	SANITARY SEWER MANHOLES & CLEANOUTS	EA	EA	Each manhole or cleanout	190202
				This includes construction and installation of manholes and cleanouts in sewage collection systems.
			G302003	LIFT STATIONS AND PUMPING STATIONS	GPM	L/S	Operating capacity	190203
				This includes construction and installation of piping and equipment in lift stations.
			G302004	PACKAGED SANITARY SEWER TREATMENT PLANTS	GPD	L/S	Operating capacity	190204
				This includes installation of pre-assembled sewage treatment plants.
			G302005	SEPTIC TANKS	GAL	L	Volume of tank	190205
				This includes installation of prefabricated septic tanks or the construction of septic tanks.
			G302006	DRAIN FIELDS	LF	M	Length of field	190206
				This includes installation of drain fields for disposal of effluent from septic tanks.
			G302090	OTHER SANITARY SEWER	XX	XX		19029X
				Sanitary sewers not described by the assembly categories listed above.
		G3030	STORM SEWER		LF	M	Length of system	1903
				This includes construction of storm water collection systems.
			G303001	STORM SEWER PIPING	LF	M	Length of piping	190301
				This includes installation of piping for collection of storm water.
			G303002	STORM SEWER STRUCTURES	EA	EA	Each manhole or cleanout
				This includes construction and installation of manholes for storm water collection systems.
			G303003	LIFT STATIONS	GPM	L/S	Operating capacity	190303
				This includes construction of lift stations including piping, pumps, and controls.
			G303004	CULVERTS	LF	M	Length of culvert	190305
				This includes construction and installation of culverts for storm water systems.
			G303005	HEADWALLS	EA	EA	Each structure	190305
				This includes construction of headwalls and installation of catch basins for storm water systems.
			G303006	EROSION & SEDIMENT CONTROL MEASURES	SY	M2	Area to control	190306
				This includes construction to control erosion due to runoff.
			G303007	STORMWATER MANAGEMENT	GAL	GAL	Volume of collection area
			G303090	OTHER STORM SEWER	XX	XX		19039X
				Storm sewers not described by the assembly categories listed above.
		G3040	HEATING DISTRIBUTION		LF	M	Length of system	1905
				This includes overhead and underground hot water, steam, and condensate piping.
			G304001	OVERHEAD HOT WATER SYSTEMS	LF	M	Length of system	190501
				This includes installation of overhead hot water supply and return piping.
			G304002	OVERHEAD STEAM SYSTEMS	LF	M	Length of system	190502
				This includes installation of overhead steam supply and condensate return piping.
			G304003	UNDERGROUND HOT WATER SYSTEMS	LF	M	Length of system	190503
				This includes installation of underground hot water supply and return piping.
			G304004	UNDERGROUND STEAM DISTRIBUTION SYSTEMS	LF	M	Length of system	190504
				This includes installation of underground steam supply and condensate return piping.
			G304005	REINFORCED CONCRETE MANHOLES & VALVE BOXES	EA	EA	Each structure
				This includes installation of prefabricated trench boxes for shoring during installation of piping.
			G304006	PUMPING STATIONS	EA	EA	Each pumping station
			G304090	OTHER HEATING DISTRIBUTION	XX	XX		19059X
				Heating distribution not described by the assembly categories listed above.
		G3050	COOLING DISTRIBUTION		LF	M	Length of system	1906
				This includes construction and installation of chilled water distribution systems.
			G305001	OVERHEAD COOLING SYSTEMS	LF	M	Length of system	190601
				This includes installation of overhead chilled water supply and return piping.
			G305002	UNDERGROUND COOLING SYSTEMS	LF	M	Length of system	190602
				This includes installation of underground chilled water supply and return piping.
			G305003	TRENCHBOXES	LF	M	Length of trench	190603
				This includes installation of prefabricated trench boxes for shoring during installation of piping.
			G305004	WELLS FOR COOLING	EA	EA	Each well
			G305005	PUMPING STATIONS	EA	EA	Each pumping station
			G305006	ON-SITE COOLING TOWERS	EA	EA	Each cooling tower
			G305090	OTHER COOLING DISTRIBUTION	XX	XX		19069X
				Cooling distribution not described by the assembly categories listed above.
		G3060	FUEL DISTRIBUTION		GAL	L	Volume of storage tank	1908
				This includes installation of piping and storage tanks for building and aviation fuels.
			G306001	LIQUID FUEL DISTRIBUTION PIPING SYSTEM	LF	M	Length of piping	190801
				This includes installation of piping for fuel and oil distribution. This includes equipment related to piping, system leak detection and tightness testing.
			G306002	AVIATION FUEL DISTRIBUTION PIPING SYSTEM	LF	M	Length of piping	190801
				This includes installation of piping for aviation fuel distribution and equipment related to the piping. This also includes system leak detection and tightness testing.
			G306003	LIQUID FUEL STORAGE TANKS	GAL	L	Volume of storage tank	190802
				This includes installation of buried or above ground fuel tanks relating to liquid fuel or aviation systems.
			G306004	LIQUID FUEL DISPENSING EQUIPMENT	EA	EA	Each piece of equipment	190803
				This includes equipment relating to liquid fuel and aviation systems.
			G306005	LIQUID FUEL SYSTEM TRENCHBOXES	LF	M	Length of trench	190804
				This includes installation of prefabricated trench boxes for shoring during installation of piping.
			G306006	GAS DISTRIBUTION PIPING (NATURAL AND PROPANE)	LF	M	Length of piping
				This includes piping for distribution of natural or propane gas.
			G306007	GAS STORAGE TANKS	GAL	L	Volume of storage tank
				This includes installation of tanks for natural or propane gas.
			G306008	GAS SYSTEM TRENCHBOXES	LF	M	Length of trench
				This includes installation of prefabricated trench boxes for shoring during installation of piping.
			G306009	OTHER GAS DISTRIBUTION	XX	XX
				Gas distribution not described by the assembly categories listed above.
			G306090	OTHER FUEL DISTRIBUTION	XX	XX		19089X
				Fuel not described by the assembly categories listed above.
		G3090	OTHER SITE MECHANICAL UTILITIES		LF	M	Length of system	1904
				This includes all systems for collection of contaminated waste requiring special treatment.
			G309001	INDUSTRIAL WASTE PIPE	LF	M	Length of piping	190401
				This includes construction and installation of all piping for collection of industrial waste.
			G309002	INDUSTRIAL WASTE MANHOLES & CLEANOUTS	EA	EA	Each manhole or cleanout	190402
				This includes construction of manholes and cleanouts for industrial waste.
			G309003	INDUSTRIAL WASTE LIFT STATIONS	GPM	L/S	Operating capacity	190403
				This includes construction and installation of industrial waste lift stations and equipment.
			G309004	INDUSTRIAL WASTE HOLDING TANKS & SEPARATORS	EA	EA	Number of tanks	190404
				This includes construction or installation of special tanks such as silver recovery tanks or separators such as oil water separators.
			G309005	INDUSTRIAL WASTE TRENCHBOXES	LF	M	Length of trench	190405
				This includes installation of prefabricated trench boxes for shoring during installation of piping.
			G309090	OTHER INDUSTRIAL WASTE	XX	XX		19049X
				Industrial waste not described by the assembly categories listed above, such as petroleum oil and lubricant distribution systems.
	G40	SITE ELECTRICAL UTILITIES			EA	EA	Systems total	20
				This system includes exterior electrical systems and equipment including substations, overhead and underground distribution systems, metering systems and equipment, exterior lighting, lightning protection systems, communication and alarm systems, and cathodic protection.
		G4010	ELECTRICAL DISTRIBUTION		KVA	KVA	Total rated capacity
				Electrical distribution includes the following: substations; transformers; switches, controls and devices; overhead electric conductors; towers, poles, crossarms and insulators; underground electric conductors; ductbanks, manholes, handholes and raceways; grounding systems; and metering.
			G401001	SUBSTATIONS	KVA	KVA	Total rated capacity	2001
				This system includes substation equipment and materials required from the primary power source.
			G401002	TRANSFORMERS	KVA	KVA	Total rated capacity	200101
				Electrical power transformers used in conjunction with electrical substations. May include pole/tower or pad-mounted transformers located outside the building.
			G401003	SWITCHES, CONTROLS & DEVICES	EA	EA	Number of separate components	200102
				Includes all components of switchgear, voltage regulators and busbars used with electrical substations.
			G401004	OVERHEAD ELECTRIC CONDUCTORS	LF	M	Length of conductor	200103
				Includes conductors used in conjunction with substations.
			G401005	TOWERS, POLES, CROSSARMS & INSULATORS	EA	EA	Number of towers and poles	200104
				Towers, poles, crossarms, and insulators used in conjunction with substations.
			G401006	UNDERGROUND ELECTRIC CONDUCTORS	LF	M	Length of conductor	200105
				Includes conductors used in conjunction with substations.
			G401007	DUCTBANKS, MANHOLES, HANDHOLES & RACEWAYS	EA	EA	Number of ductbanks and access points	200106
				Components used in conjunction with electrical substations.
			G401008	GROUNDING SYSTEMS	EA	EA	Number of systems	200108
				Grounding systems used in conjunction with substations. Grounding systems for buildings, power distribution, and other electrical systems and subsystems are included with those other systems.
			G401009	METERING	EA	EA	Number of meters	200208
				Includes components used in conjunction with exterior electrical distribution.
			G401010	CATHODIC PROTECTION	EA	EA	Each system
				Includes a system used in conjunction with exterior electrical distribution for corrosion control.
			G401011	EQUIPMENT REQUIREMENTS FOR COASTAL AND HIGH HUMIDITY AREAS	XX	XX		0
			G401090	OTHER ELECTRIC TRANSMISSION & DISTRIBUTION	XX	XX		20019X
				Substations not described by the assembly categories listed above.
		G4020	SITE LIGHTING		LF	M	Length of distribution	2003
				Exterior electrical lighting systems including conductors, switches, controls and other devices, supporting structures, grounding systems, and all other equipment required to support a lighting system.
			G402001	EXTERIOR LIGHTING FIXTURES & CONTROLS	EA	EA	Number of fixtures	200301
				Includes fixtures, controls, and all components used in conjunction with exterior lighting.
			G402002	SPECIAL SECURITY LIGHTING SYSTEMS	EA	EA	Number of systems	200302
				Includes all components used for special security lighting.
			G402003	OTHER AREA LIGHTING	EA	EA	Number of fixtures	200303
				Includes components and equipment used for area lighting.
			G402004	LIGHTING POLES	EA	EA	Number of towers and poles	200304
				Poles used to support lighting fixtures and support equipment.
			G402005	UNDERGROUND ELECTRIC CONDUCTORS	LF	M	Length of conductor	200305
				Includes conductors for underground electrical distribution to lighting systems.
			G402006	DUCTBANKS, MANHOLES & HANDHOLES	EA	EA	Number of ductbanks and access points	200306
				Includes all components used in conjunction with exterior lighting.
			G402007	GROUNDING SYSTEMS	EA	EA	Number of systems	200307
				Grounding systems used in conjunction with exterior lighting.
		G4030	SITE COMMUNICATION AND SECURITY		LF	M	Length of distribution	2004
				This system includes cables, ductbanks, manholes, and all other equipment required to support exterior communication and alarm systems.
			G403001	TELECOMMUNICATIONS SYSTEMS	LF	M	Length of distribution	200401
				Includes all components, cables, and equipment used in conjunction with exterior telephone systems.
			G403002	CABLE TV SYSTEMS (CATV)	LF	M	Length of distribution	200404
				Includes all components, cables, and equipment used in conjunction with exterior cable TV systems.
			G403003	CABLES & WIRING	LF	M	Length of conductor	200501
				Includes cables, wiring, and equipment used in conjunction with exterior security systems.
			G403004	DUCTBANKS, MANHOLES & HANDHOLES	EA	EA	Number of ductbanks and access points	200502
				Includes ductbank, manholes, and handholes used in conjunction with exterior security systems.
			G403005	TOWERS, POLES & STANDS	EA	EA	Number of towers, poles and stands	200503
				Includes towers, poles, stands, and equipment used in conjunction with exterior security systems.
			G403006	TV CAMERAS & MONITORS	EA	EA	Number of cameras and monitors	200504
				Includes cameras, monitors, and components used in conjunction with exterior security systems.
			G403007	ELECTRONIC SECURITY SYSTEMS (ESS)	EA	EA	Number of systems	200505
				Includes components and systems used in conjunction with exterior security systems.
			G403008	OTHER COMMUNICATION & ALARM	XX	XX		180601
				Includes all components, cables, and equipment used in conjunction with other special communication and alarm systems not defined above.
			G403009	GROUNDING SYSTEMS	EA	EA	Number of systems	200505
				Includes grounding systems used in conjunction with exterior security systems.
			G403090	OTHER SECURITY SYSTEMS	XX	XX		20059X
				Includes all components and equipment used in conjunction with special security systems not defined above.
		G4090	OTHER SITE ELECTRICAL UTILITIES		LF	M	Length of conductor
				This system includes alternate energy sources. This system also includes sacrificial anodes, induced current conductors, and components used in conjunction with cathodic protection.
			G409001	SACRIFICIAL ANODE CATHODIC PROTECTION SYSTEM	EA	EA	Number of anodes	20601
				Includes all components required in conjunction with sacrificial anode system.
			G409002	INDUCED CURRENT CATHODIC PROTECTION SYSTEM	LF	M	Length of conductor	20602
				Includes conductors and termination required for cathodic protection.
			G409003	EMERGENCY POWER GENERATION	KVA	KVA	Total rated capacity
			G409090	OTHER CATHODIC PROTECTION	XX	XX		2069X
				Includes components and equipment used in conjunction with other cathodic protection systems not defined above.

	G90	OTHER SITE CONSTRUCTION			LS	LS
				Other site construction includes service and pedestrian tunnels, bridges, railroad spurs, and snow melting systems.
		G9010	SERVICE AND PEDESTRIAN TUNNELS		XX	XX
				This assembly includes service and pedestrian tunnels.
			G901001	CONSTRUCTION OF SERVICE AND PEDESTRIAN TUNNELS	LF	M	Length of tunnel
				This assembly includes construction of service and pedestrian tunnels.
			G901002	PREFABRICATED SERVICE AND PEDESTRIAN TUNNELS	LF	M	Length of tunnel
				This assembly includes prefabricated service and pedestrian tunnels.
		G9090	OTHER SITE CONSTRUCTION		XX	XX
				Other site construction includes bridges, railroad spurs and snow melting systems.
			G909001	BRIDGES	SY	M2	Area of structure	180601
				Bridges included here are typically small spans or overpasses that are not meant to be used to estimate spans over large bodies of water. Options exist for cast-in-place concrete T-beam, precast I-beam, precast box, concrete and steel composite, laminated timber deck bridge structures.
			G909002	RAILROAD SPURS	LF	M	Length of track	180602
				Railroad assemblies exist for 110, 115, and 132 lb. tracks and ties. Turnouts, roadway crossings, derailleurs, stops, and bumpers are also included.
			G909003	SNOW MELTING SYSTEMS	EA	EA	Number of systems
			G909090	OTHER SPECIAL CONSTRUCTION	XX	XX		18069X
				Any special construction not covered in the above categories.

Section H - Waterfront

Unf L1	Unf L2	Unf L3	WBS L4	Definition	E UOM	M UOM	Quantity Definition
H	WATERFRONT
	H10	WATERFRONT STRUCTURES			LS	LS
				Waterfront Structures including wharves, piers, dolphins, trestles, and other structures and appurtenances necessary for the safe mooring of vessels and to support waterfront operations.
		H1010	SUBSTRUCTURE		XX	XX
				This assembly includes substructure components for waterfront structures, such as pile foundations, pile caps, quays, relieving platforms, revetments, seawalls, boat ramps, cut-off walls, firewalls, and hanging panels.
			H101001	PILE FOUNDATIONS	VLF	VM	Length of piles
			H101002	PILE CAPS	XX	XX
			H101003	QUAYS	XX	XX
			H101004	RELIEVING PLATFORMS	XX	XX
			H101005	REVETMENTS	XX	XX
			H101006	SEAWALLS	XX	XX
			H101007	BOAT RAMPS	XX	XX
			H101008	CUT-OFF WALLS	XX	XX
			H101009	FIREWALLS AND HANGING PANELS	XX	XX
			H101090	OTHER SUBSTRUCTURE COMPONENTS	XX	XX
		H1020	SUPERSTRUCTURE		XX	XX
				This assembly includes superstructure components for waterfront structures, such as beams and girders, columns, utility enclosures, and other features that support the operation deck area.
			H102001	BEAMS AND GIRDERS	XX	XX
			H102002	COLUMNS	XX	XX
			H102003	UTILITY ENCLOSURES	XX	XX
			H102090	OTHER SUPERSTRUCTURE ELEMENTS	XX	XX
		H1030	DECK		XX	XX
				This assembly includes the components for the deck, including elevated deck, on-grade deck, deck overlays, curbs and bullrails, mooring hardware foundation, high mast lighting foundations, utility mounds, expansion joints, guard post and railings, paint striping and other related features.
			H103001	DECK	XX	XX
			H103002	ON-GRADE SLAB	XX	XX
			H103003	DECK OVERLAY	XX	XX
			H103004	CURBS AND BULLRAILS	XX	XX
			H103005	MOORING FOUNDATIONS	XX	XX
			H103006	HIGH MAST LIGHTING FOUNDATIONS	XX	XX
			H103007	UTILITY MOUNDS	XX	XX
			H103008	EXPANSION JOINTS	XX	XX
			H103009	GUARD POSTS AND RAILING	XX	XX
			H103010	PAINT STRIPING	XX	XX
			H103090	OTHER DECK COMPONENTS	XX	XX
		H1040	MOORING AND BERTHING SYSTEM		XX	XX
				This assembly includes the components for the mooring hardware and fendering systems, including foundations, anchor bolts, and support systems.
			H104001	PRIMARY FENDER SYSTEM	XX	XX
			H104002	SECONDARY FENDER SYSTEM	XX	XX
			H104003	CORNER FENDER SYSTEM	XX	XX
			H104004	DOLPHINS	XX	XX
			H104005	MOORING HARDWARE	XX	XX
			H104090	OTHER MOORING AND BERTHING COMPONENTS	XX	XX
		H1050	APPURTENANCES		LS	LS
				This assembly includes the appurtenances such as handrails, brows, cable booms, floats, safety ladders, life rings, oil containment booms, and other similar features.
	H20	GRAVING DRYDOCKS			LS	LS
	H30	COASTAL PROTECTION			LS	LS
				Coastal Protection System consists of all waterfront breakwaters, wave protection armor, slope protection, revetments, and other features necessary and required for the protection of waterfront facilities from damage by wave, tide and current.
		H3010	WAVE PROTECTION		XX	XX
				This assembly includes required wave protection features, such as breakwaters, wave protection armor for slope protection, revetment and scour protection.
			H301001	WAVE PROTECTION ARMORS	XX	XX
			H301002	BREAKWATERS	XX	XX
		H3020	SLOPE PROTECTION		XX	XX
				This assembly includes required slope protection features, such as revetment or embankment dikes.
			H302001	ROCK REVETMENTS	XX	XX
			H302002	GRANULAR FILL REVETMENTS	XX	XX
			H302003	COMBINED ROCK AND GRANULAR FILL REVETMENTS	XX	XX
	H40	NAVIGATION DREDGING AND RECLAMATION			LS	LS
				Navigation Dredging and Reclamation System consists of all dredging of navigation channels, approaches, turning basins, and berthing areas near piers, wharves, dolphins, and reclamation as necessary to navigate the vessels to the berths and produce reclaimed land to support construction of the waterfront facilities.
		H4010	DREDGING		XX	XX
		H4020	DREDGING DISPOSAL		XX	XX
			H402001	OCEAN DISPOSAL	XX	XX
			H402002	NEW CONFINED DISPOSAL FACILITIES	XX	XX
			H402003	EXISTING CONFINED DISPOSAL FACILITIES	XX	XX
		H4030	RECLAMATION		XX	XX
	H50	WATERFRONT UTILITIES			LS	LS
				The Waterfront Utility System consists of civil/mechanical utilities, electrical utilities, and fire protection to be installed on waterfront structures
		H5010	CIVIL/MECHANICAL UTILITIES		XX	XX
			H501001	POTABLE WATER	XX	XX
			H501002	SALTWATER	XX	XX
			H501003	SANITARY SEWER	XX	XX
			H501004	BILGE AND OILY WASTE	XX	XX
			H501005	STEAM	XX	XX
			H501006	COMPRESSED AIR	XX	XX
			H501090	OTHER CIVIL/MECHANICAL UTILITIES	XX	XX
			H501091	MISCELLANEOUS MATERIAL	XX	XX
		H5020	ELECTRICAL UTILITIES		XX	XX
			H502001	POWER DISTRIBUTION SYSTEM	XX	XX
			H502002	TELECOMMUNICATION SYSTEM	XX	XX
			H502003	LIGHTING SYSTEMS	XX	XX
			H502004	LIGHTNING PROTECTION SYSTEM	XX	XX
			H502005	POWER BOOMS	XX	XX
			H502090	OTHER ELECTRICAL UTILITIES	XX	XX
		H5030	WATERFRONT FIRE PROTECTION		XX	XX
			H503001	FIRE PROTECTION WATER DISTRIBUTION SYSTEM	XX	XX
			H503002	FIRE ALARM	XX	XX
	H60	WATERFRONT DEMOLITION			LS	LS
		H6010	IN OR OVER-WATER DEMOLITION		XX	XX
		H6020	NON IN OR OVER-WATER DEMOLITION		XX	XX
		H6030	HAZARDOUS COMPONENTS ABATEMENT		XX	XX
	H70	WATERFRONT ATFP			LS	LS
		H7010	WATERSIDE ATFP		XX	XX
		H7020	LANDSIDE ATFP		XX	XX